2)
Set the Z-Wave network main controller into learning mode
(see Z-Wave network controller operating manual).
3)
Triple-clicking the Z-Button within 1.5 seconds.
4)
If the inclusion is successful, the LED will blink fast for less
than 5 seconds and then keep on. Otherwise, the LED will
blink 5 seconds and then keep blinking slowly, in which case
you need to repeat the process from step 2.
To include AV Control into a Z-Wave network as a security device:
1)
Make sure the power supply is connected and the AV Control is
located within a direct Z-Wave network's main controller
communication range.
2)
Set the Z-Wave network main controller into learning mode
(see Z-Wave network controller operating manual).
3)
Pressing and holding the Z-Button for 3 seconds.
4)
If the inclusion is successful, the LED will blink for less than 5
seconds and then keep on. Otherwise, the LED will blink 5
seconds and then keep blinking slowly, in which case you need
to repeat the process from step 2.
TIP:
If you want your AV Control to be a security device that use
secure/encrypted message to communicate in a Z-Wave network,
then a security enabled Z-Wave controller is needed.
5.
REMOVING FROM Z-WAVE NETWORK
To remove the AV Control from the Z-Wave network:
1)
Make sure the power supply is connected and the AV Control is
located within a direct Z-Wave network's main controller
communication range.
2)
Set the Z-Wave network main controller into exclusion mode.
3)
Triple-clicking the Z-Button within 1.5 seconds.
4)
If the remove for exclusion is successful, LED will blink fast for
less than 5 seconds and keep blinking slowly. Otherwise, LED will
blink for 5 seconds and then keep on, in which case you need to
repeat the process from step 2.
NOTE:
Remove procedure will clear the AV Control’s memory which means
it will erase all information about Z-Wave network and advanced
configuration.
6.
RESET IR TRANSCEIVER
Reset procedure will clear the AV Control 's memory, including Z-
Wave network information, but not including IR information.
To reset AV Control:
Pressing and holding the Z-button for 20 seconds. Release the
button after 20 seconds, LED will be on for 3 seconds, and then LED
will keep blinking. AV Control will send "Device_Reset_Locally" to
the main controller and exclude from the Z-Wave network. This
procedure will reset AV Control to factory default.
NOTE:
Use this procedure only in the event that the network primary
controller is missing or otherwise inoperable.
7.
ASSOCIATION
AV Control supports only one association group:
Grouping Identifier
Max Nodes
Send Commands
Group 1
0x05
NULL
8.
ADVANCED CONFIGURATION
AV Control offers a wide variety of advanced configuration
settings. Below parameters can be accessed from main
controller’s configuration interface (Cockpit App).
Parameter No.93 Clear IR information
Clear all IR information.
Value: 1431655765
Default: 1
Parameter size: 4[byte]
Parameter No.254 Enable/disable the configuration command
Lock/unlock all configuration parameters.
O— Unlock.
1 — Lock.
Default setting: O
Parameter size: I[byte]
Parameter No.255 Reset Scene Controller
Reset to factory default settings and removed from the Z-Wave
network.
Value: 1431655765
Default: 1
Parameter size: 4[byte]
9.
TECHNICAL SPECIFICATIONS
Power supply:
USB Power DC 5V 1A
IR Coverage
IR Coverage: 360 degree, 7~10 m
Z-wave operation
range:
About 40m indoors (depending on building
materials)
Temperature
Operation: 0 - 40°C
Storage: -10 - 50°C; 0-90% RH
Dimension
85x85x26cm
Working current:
About 60mA
Standby current:
About 35uA
IMPORTANT DISCLAIMER!
Z-Wave wireless communication is not always 100% reliable. This
device should not be used in situations in which life and/or valuables
are solely dependent on its functioning.
WARNING!
Do not dispose of electrical appliances as unsorted municipal
waste, use separate collection facilities.
Contact your local government for information regarding the
collection systems available.
If electrical appliances are disposed of in landfills or dumps,
hazardous substances can leak into the groundwater and get into the
food chain, damaging your health and well-being.
When replacing old appliances with new once, the retailer is legally
obligated to take back your old appliance for disposal free of charge.
Cockpit Smart Home d.o.o.
Ulica Klementa Juga 007
5250 Solkan, Slovenia
Web:
Tel: +386 5 335 95 00
Date: 03.10.2018
Document: Cockpit SL _AV Control user manual_V1_eng
