Cobra MRF77, Manual

Page: 3 / 23

É Ê
! " # $ % " ! " # $ % "
š ›
œ > D BA
› 
HA ž>
= ;
Ÿ D
š ›
œ > D BA
› 
HA ž>
= ;
Ÿ D
0HPRU\&KDQQHOV
You can program (or tag) any or all channels to be scanned in the
Memory
Scan
mode.
To Program Memory Channels:
1.
From
Standby
mode, select a channel to be tagged using
the
Up/Down
buttons.
2. Press the MORE soft key (if necessary), then the MEM
soft key
. The channel will be tagged for scanning and
MEM (memory channel) will appear on the LCD whenever
that channel is selected.
Repeat steps 1 through 2 to add addition memory
channels.
To Clear Memory Channels:
1.
From
Standby
mode, select a channel to be cleared
from a memory tagging using the
Up/Down
buttons.
2.
Press and hold the
MORE soft key
(if necessary), then
the
MEM soft key
. The channel will be untagged and
MEM
(memory channel) will no longer appear on the LCD
whenever that channel is selected.
Repeat steps 1 through 2 to clear additional channels
from memory locations.
0HPRU\6FDQ
During
Memory Scan
, the radio will rapidly switch from
tagged channel to tagged channel. Whenever any activity is
detected, the radio will stop the scan to allow you to listen
to the activity on that channel. The radio will then continue
to scan after 2 seconds of inactivity, unless you switch out of
the
Memory Scan
mode.
88 30
60 75
Å Ë
® « ¯ " ° ­ # " ±
² ² ³ ´ µ
¶
· ¸ ¹ ½ p » u u r
´ ¼ ¼ ¹
¶
¸ ¹ · º
´ ¼ ½ ¾ ¿ À
³ µ Á ¹ ³ ² ² Â ² ¼
o
o
à ½ ½ Ä p q r r u » o j
Å " Æ Ç È ±
² ² ³ ´ µ
¶
· ¸ ¹ ½ p » u u r
´ ¼ ¼ ¹
¶
¸ ¹ · º
´ ¼ ½ ¾ ¿ À
³ µ Á ¹ ³ ² ² Â ² ¼
o
o
à ½ ½ Ä p q r r u » o j
Ì Í Ì
NOTE
If there are fewer than two (2) channels tagged,
the
Memory Scan
mode will not be available.
[See page 47 under program memory channels
to tag at least two (2) channels.]
NOTE
The radio must be squelched for the Memory Scan mode
to function. See page
26
for squelch procedure.
To Enter Memory Scan:
1. From Standby mode, press the MORE soft key (if
necessary), then the
SCAN soft key
.
The radio will immediately begin to scan the channels you
tagged.
SCAN
(memory scan) will be highlighted on the LCD.
To Exit Memory Scan:
1.
From
Memory Scan
mode, press the
SCAN soft key
.
This will return the radio to
Standby
mode on the last
scanned memory location.
During Memory Scan (while receiving an incoming
transmission), You Can Choose From The Following:
a.
Press the
Talk
button to remain on that memory
location and end scanning. This will return the radio
to
Standby
mode.
The radio will then continue to scan after 2 seconds of
inactivity, unless you switch out of the
Memory Scan
mode.
During Memory Scan (while not receiving a
transmission):
b. Press the Talk button to communicate on the last
channel scanned and return to
Standby
mode.
6WDQGE\0RGH
6WDQGE\0RGH
Å " Æ Ç È ±
² ² ³ ´ µ
¶
· ¸ ¹ ½ p » u u r
´ ¼ ¼ ¹
¶
¸ ¹ · º
´ ¼ ½ ¾ ¿ À
³ µ Á ¹ ³ ² ² Â ² ¼
o
o
à ½ ½ Ä ¿ Î À º u » o j
u j u
~  €  
‚
~ ƒ „
‚
† ‡ ˆ  ƒ ‰ Š † „
‹
Œ

Ž Ž  •
‘
  “ ”  • ” “ – “ 
—
’ ˜ ‡ ~