background image

Customer Assistance

Warranty

Introduction

9

Operation

8

Mode Functions

Remember, you can achieve maximum
range by using maximum range
extender. See page 6 for details.

Scrolling through Mode Functions

By scrolling through the

Mode Functions

, you will be able to

select or turn

on/off

preferred features of your microTALK radio.

When scrolling through the

Mode Functions

, your radio features

will be displayed in the following order:

Set CTCSS Privacy Codes
Set DCS Privacy Codes
Set NOAA All Hazards Radio Channel
Set VOX On/Off
Set VOX Sensitivity Level
Set Memory Locations
Set Channel Scan
Set CTCSS Privacy Code Scan
Set DCS Privacy Code Scan
Set Memory Location Scan
Set VibrAlert and/or Call Alert
Set Call Alert Tone Signal
Set Roger Beep On/Off
Set Keystroke Tones On/Off

Scroll through the mode functions using the

Mode

button. Each press

and release of the

Mode

button will advance to the next mode function.

Press the

Talk

button at any point to return the radio to

Standby

mode.

Privacy Codes

Your microTALK radio incorporates two advanced coded squelch
systems that can help to reduce interference from other users
on any given channel. CTCSS (Continuous Tone Coded Squelch
System) provides 38 privacy codes and DCS (Digitally Coded
Squelch) provides 83 privacy codes. This provides a total of 121

Privacy Codes

. Either system can be used on all channels, but both

systems cannot be used on the same channel at the same time.

To successfully communicate using a privacy code, both
the sending and receiving radios must be tuned to the same
channel and to the same privacy code system (CTCSS or
DCS) and privacy code number. Each channel will remember
the last privacy code system and number you select.

Operation

The privacy code 00 is not a privacy code, but allows all
signals to be heard on a channel that is set to 00 on both
the CTCSS and DCS systems.

Set CTCSS Privacy Codes

To select a CTCSS privacy code:

1.

After selecting a channel, press the

Mode

button until the CTCSS icon appears

and the small numbers flash on the display
(01 through 38).

NOTE

If DCS is turned

on

at the channel

selected, the display will flash the
CTCSS icon and “OFF.” To switch from
DCS to CTCSS, press the

Channel Up

or

Channel Down

button while the

display is flashing “OFF.” The display
will then show the small numbers
flashing and you will then be able
to proceed to step 2.

2.

Press using the

Channel Up

or

Channel

Down

button to select a CTCSS privacy

code. You can hold the

Channel Up

or

Channel Down

button for fast advance.

3.

When your desired CTCSS privacy code is
displayed, choose one of the following:

a.

Press the

Mode

button to enter the new

setting and proceed to other functions.

b.

Press the

Lock/Enter

button to enter the

new setting and return to

Standby

mode.

Mode Button

Mode Button

Channel Buttons

CTCSS Privacy Code

Summary of Contents for microTalk LI 6500 WX


















Reviews: