background image

Customer Assistance

Warranty

Introduction

Operation

During scanning (while not receiving a transmission),
you can choose from the following:

a.

Press and hold the

Talk

button to communicate on the

channel or channel/privacy code that was displayed before
you entered mode functions or the channel on which,
during scanning, you last received a transmission.
This will return the radio to

Standby

mode.

b.

Press the

Mode/Power

button to proceed to set privacy

code scan on the channel that was either displayed before
you entered mode functions or on which, during channel
scanning, you last received a transmission (see page 12
for further details).

c.

Press the

Lock

button to return to

Standby

mode on the

channel/privacy code that was displayed before you entered
mode functions or the channel on which, during scanning,
you last transmitted or received.

Privacy Code Scan

Your microTALK radio can automatically scan the

Privacy Codes

(either CTCSS 01 through 38 or DCS 01 through 83) within one
channel. Only one set of privacy codes (CTCSS or DCS) can be
scanned at a time.

To scan privacy codes:
1.

While in

Standby

mode, press the

Channel Up

or

Channel Down

button

to choose the channel on which you
wish to scan privacy codes.

2.

Press the

Mode/Power

button until either

the CTCSS or the DCS icon appears on the
display and the

Scan

icon and the privacy

code numbers flash on the display.

3.

Press the

Channel Up

or

Channel Down

button to begin scanning privacy codes
within the channel you selected.

Mode Functions

Channel Scan

Your microTALK

®

radio can automatically scan channels.

To scan channels:
1.

Press the

Mode/Power

button until the

Scan

icon and the channel numbers appear

on the display.

2.

Press the

Channel Up

or

Channel Down

button

to begin scanning channels.

The radio ignores specific privacy
codes while scanning channels.

The

Scan

icon will continue to be displayed

when scan is

on

. Your radio will continue to

scan all channels and stop if an incoming
transmission is detected. Your radio will
remain on that channel for 10 seconds.

While setting channel scan, if you do not press any buttons for 15 seconds
your radio will automatically return to

Standby

mode on the channel or

channel/privacy code displayed before you entered mode functions.

During scanning (while receiving an incoming transmission),
you can choose from the following:

a.

Press and hold the

Talk

button to communicate on

that channel. Your radio will remain on that channel
and return to

Standby

mode.

b.

Press the

Channel Up

or

Channel Down

button to

resume scanning channels.

If you press the

Talk

button while scanning and not within

10 seconds of receiving a transmission, you will transmit
on the channel on which you last received a transmission.
This will return the radio to

Standby

mode.

If you do not press any button within 10 seconds, your
radio will automatically resume scanning channels.

10

11

Operation

Mode Functions

Channel Button

Mode/Power

Scan Channels

Channel Button

Mode/Power

Select Channel

Scan Privacy Codes

Nothing

Comes Close to a Cobra

®

Summary of Contents for microTALK CXT90












Reviews: