background image

Quick Start

1.

  Press and hold the 

Mode/Power

 button  

to turn 

on

 your radio.

2.

  Press the 

Channel Up

 or 

Channel Down

  

button to select a channel.

Both radios must be tuned to the same 

channel/privacy code to communicate.

3.

  Press and hold the 

Talk

 button while  

speaking into the microphone.

4.

  When finished talking, release the 

Talk

  

button and listen for a response.

Customer Assistance Warranty

Introduction

Operation

Battery Low 

 

    When battery power is low, the 

Battery Low

 icon 

will blink. Your batteries should be replaced or 

recharged, if using rechargeable batteries.

Auto Battery Save 

 

If there are no transmissions within 10 seconds, 

the radio will automatically switch to 

Battery Save 

mode and the 

Power Saver

 icon will flash in the 

display. This will not affect the radio’s ability to 

receive incoming transmissions.

Communicating with Another Person 

1.

 Press and hold the 

Talk

 button.

2.

  With the microphone about two inches (5 cm) from 

your mouth, speak in a normal voice.

3.

  Release the 

Talk

 button when you are  

finished talking and listen for a response.

You cannot receive incoming calls while  

pressing the 

Talk

 button.

Both radios must be tuned to the  

same channel to communicate.

  

2

To charge batteries in radio:
1.

  Check to see that the batteries have been 

inserted properly. 

2.

  Insert the wall charger/adapter into the charge 

jack located at the top of the radio. 

3.

  Plug the wall charger/adapter into electrical 

outlet.

Use only the supplied rechargeable batteries and charger for recharging 

your Cobra microTALK radio.
Cobra recommends your radio is turned off while being charged.
Non-rechargeable alkaline batteries can also be used in your radio.

Using Your Radio

Operation

3

Battery Low

Turning on Your microTALK

®

 Radio 

  Press and hold the 

Mode/Power

 button until you hear 

a series of audible tones indicating the radio is 

on

.

Your microTALK

®

 radio is now in 

Standby 

mode, 

ready to receive transmissions. The radio is always 

in 

Standby 

mode except when the 

Talk

Call

 or 

Mode/Power 

buttons are pressed.

Mode/Power

Talk Button

Battery Save Mode

Two Inches (5 cm) 
from Mouth

To Select a Channel   

 With the radio 

on

, select any of the 22 channels by 

pressing the 

Channel Up

 or 

Channel Down

 button. 

Both radios must be tuned to the  

same channel to communicate.

Channels 1 through 7 are shared with FRS/ GMRS. 

Channels 8 through 14 are FRS only. Channels 15 

through 22 are GMRS only.  

See 

page 14

 for FRS/GMRS frequency 

allocations and compatibility charts.

Channel Button

Channel Number

Nothing 

Comes Close to a Cobra

®

Radio Charger Jack

CXT280_MANL_vB.indd   2-3

5/16/13   4:08 PM

Summary of Contents for microTALK CXT280












Reviews: