COBHAM Sea Tel 4010W-33 Installation Manual Download Page 84

Page: 84 / 141

4010W-33 Installation Manual

Installation Troubleshooting

16-2

Verify that the stow pin is engaged in the
channel of the stow block (as shown).

Verify that the antenna does NOT rotate.

17.1.2.

Installing the EL Shipping/Stow Restraint

The EL Shipping/Stow restraint is formed by a

Stow pin-bolt mounted through a bracket and
is engaged into a hole in the elevation pan

when the dish is up at zenith (90 degrees

elevation).

In the un-stowed position the hardware from

right to left is Stow pin-bolt head, hex nut,

washer, bracket, washer, hex nut, so that the
pin section of the Stow pin-bolt is not

inserted into the hole in the elevation pan.

Pin inserted NOT in the Elevation Pan

Hex Nut  and Washer

Bracket

Washer, Hex Nut and EL Stow Pin-Bolt head

To restrain the elevation axis of the antenna,

unthread the hex nut nearest the elevation

pan. Remove the hex nut and washer from

the stow pin-bolt.

Remove the stow pin-bolt from the bracket.

Summary of Contents for Sea Tel 4010W-33














































































































































Search results

Summary of Contents for Sea Tel 4010W-33

Reviews:

Brands by name

Popular brands

COBHAM Sea Tel 4010W-33, Installation Manual

Search results

Summary of Contents for Sea Tel 4010W-33

Reviews:

Brands by name

Popular brands