Cobalt Digital Inc BBG-1022-FS-DSP Product Manual Download | Manualshive

Page: 115 / 124

background image

BBG-1022-FS-DSP-OM (V1.2)

BBG-1022-FS-DSP PRODUCT MANUAL

3-83

Setup/Operating Instructions

Troubleshooting

Troubleshooting

This section provides general troubleshooting information and specific
symptom/corrective action for the BBG-1022-FS-DSP and its remote control
interface. The BBG-1022-FS-DSP requires no periodic maintenance in its
normal operation; if any error indication (as described in this section) occurs,
use this section to correct the condition.

Error and Failure Indicator Overview

The BBG-1022-FS-DSP itself and its remote control provide error and failure
indications. Depending on how the BBG-1022-FS-DSP is being used (i.e,
standalone or network controlled through DashBoard™ or a Remote Control
Panel), check all available indications in the event of an error or failure
condition.

The various BBG-1022-FS-DSP device and remote control error and failure
indicators are individually described below.

Note:

The descriptions below provide general information for the various status and
error indicators. For specific failures, also use the appropriate subsection
listed below.

• Basic Troubleshooting Checks (p. 3-85)

• BBG-1022-FS-DSP Processing Error Troubleshooting (p. 3-85)

«
...
113
114
115
116
117
...
»

Summary of Contents for BBG-1022-FS-DSP





























































































































Reviews:

No comments

Related manuals for BBG-1022-FS-DSP

Brand: Datavideo Pages: 10

Brand: VAD Pages: 18

Brand: Gama Sonic Pages: 4

Brand: Harman Kardon Pages: 6

Brand: Harman Kardon Pages: 16

Brand: R&S Pages: 60

Brand: Vanner Pages: 44

Brand: Wyrestorm Pages: 4

Brand: RGBlink Pages: 46

Brand: Danpex Pages: 4

Brand: I-Tech Pages: 16

Brand: EASYLITE Pages: 44

Brand: Nyrius Pages: 11

SA-1000K Series

Brand: Samlexpower Pages: 23

Brand: Bush Pages: 42

Brand: INVT Pages: 174

SC-TDC-1000 D Series

Brand: Surface Concept Pages: 28

Brand: UNICOM Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands