manualshive.com logo in svg

Cobalt Digital Inc 9922-FS, Product Manual, Page: 26 / 118

Share
Download
Cobalt Digital Inc 9922-FS Product Manual Download Page 26

1

Technical Specifications

1-22

9922-FS PRODUCT MANUAL

9922FS-OM (V1.5)

9922-FS Rear I/O Modules

The 9922-FS physically interfaces to system video connections at the rear of 
its frame using a Rear I/O Module. 

All inputs and outputs shown in the 9922-FS Functional Block Diagram 
(Figure 1-1) enter and exit the card via the card edge backplane connector. 
The Rear I/O Module breaks out the 9922-FS card edge connections to BNC 
and other connectors that interface with other components and systems in the 
signal chain.

The full assortment of 9922-FS Rear I/O Modules is shown and described in 
9922-FS Rear I/O Modules (p. 2-4) in Chapter 2, “Installation and Setup”.

Technical Specifications

Table 1-1 lists the technical specifications for the 9922-FS 3G/HD/SD-SDI 
Frame Sync with Audio/Video Processing, AES/Analog Audio Embedding/
De-Embedding, CVBS I/O, and Dual-Channel Option (+2FS) card.

Table 1-1

Technical Specifications

Item

Characteristic

Part number, nomenclature

9922-FS 3G/HD/SD-SDI Frame Sync with Audio/Video 
Processing, AES/Analog Audio Embedding/De-Embedding, CVBS 
I/O, and Dual-Channel Option (+2FS) 

Installation/usage environment

Intended for installation and usage in frame meeting openGear™ 
modular system definition

Power consumption

< 18 Watts maximum

Installation Density

Up to 20 cards per 20-slot frame

Environmental:

Operating temperature:
Relative humidity (operating or storage):

32° – 104° F (0° – 40° C)
< 95%, non-condensing

Frame communication

10/100 Mbps Ethernet with Auto-MDIX

Indicators

Card edge display and indicators as follows:

• 4-character alphanumeric display

• Status/Error LED indicator

• Input Presence LED indicators

Serial Digital Video Input

Number of Inputs:

Up to (4), with manual select or failover to alternate input. 

Data Rates Supported:

SMPTE 424M, 292M, SMPTE 259M-C

Summary of Contents for 9922-FS























































































































Reviews:

No comments