background image

ExpressMix

 

Chemical Dispenser

Instruction Manual

Safety Precautions

WEAR:

 

Protective clothing and eyewear when dispensing chemicals or other materials or when working in the vicinity of all chemicals, or 
filling or emptying equipment.

ALWAYS:

 

Observe safety and handling instructions of the chemical manufacturer.

 

Direct discharge away from you or other persons or into approved containers.

 

Dispense cleaners and chemicals in accordance with manufacturer’s instructions. Exercise CAUTION when maintaining your 
equipment.

 

Reassemble equipment according to instruction procedures. Be sure all components are firmly screwed or latched into position.

KEEP:

 

Equipment clean to maintain proper operation.

ATTACH:

 

Only to water tap outlets (25 PSI Minimum, 85 PSI Maximum and Maximum water temperature 120°F).

NOTE:

 

If the unit is used to fill a sink or the discharge hose can be placed into a sink, the unit must be mounted so that the bottom of the 
cabinet is above the overflow rim of the sink.

Introduction

Installation and Operation

Installation

1.  Find suitable place close to a water source for dispenser. Remove wall bracket from packaging, place level on wall and mark (3) mounting 

holes. Drill (3) 5/16" holes and install anchors in wall. Secure wall bracket to wall with screws and washers provided.

Package Contents

1) ExpressMix

 Wall Mount Dispenser 

2)  Wall Bracket
3)  Mounting Hardware

4)  Drip Tray
5) Keys

Tools Needed 

1)  Drill and 5/16" Drill Bit
2) Screwdriver 

3) Level
4) Hammer

2.  Place the dispenser onto the wall bracket aligning the tabs with the slots in the top of the dispenser. Also ensure the central snap on top of 

the wall bracket engages the dispenser.

WARNING!

 This chemical proportioning system should be installed and serviced in accordance with these instructions. 

The customer is responsible for confirming that installation and service are performed in compliance with all national 
and local plumbing, building and other applicable laws, codes and ordinances. Staples is not responsible for improper 
installation nor product failure due to improper installation.

Screws, Washers, and

Drywall Anchors

Summary of Contents for ExpressMix









Reviews: