background image

NO HEAT OR HEAT TOO LOW 

HOT TUB LIGHT WON’T COME ON 

 
PUMP WILL NOT PRIME 

 
JETS WON’T COME ON 

 

 
LOW WATER FLOW 

TROUBLESHOOTING GUIDE 

Probable Cause 

Recommended Action  

Breaker OFF 

Turn breaker OFF then ON twice. On the cord and main breaker for 
the house if necessary. 

Inadequate water flow due to dirty filter. 

Clean filter cartridge.  

Pump not primed.  

Refer to the section of this guide on pump priming. O-ring may be 
missing or damaged on air bleeds.  

Improper line voltage.  

Have a 

Licensed Electrician

 check the line voltage.  

Probable Cause 

Recommended Action 

Light bulb burnt out 

Replace bulb (non warranty) 

Dirty Connection 

Check to see if there is anything covering the connection on the 
housing that holds the light bulb 

Probable Cause 

Recommended Action  

Pump on but no water flow 

Loosen top bleeder valve on pump until water comes out steadily.  

No water in pump 

Make sure water level in hot tub is midway up the skimmer wall 
fitting . Open the top pump bleed valve on face of pump until   
water flows out.  

Air lock 

Bleed off air at bleeder valve.  

Blocked lines 

Check skimmer, suction for blockage.  

Pump surges (jets lose power then come 
back, then lose power again) 

Check water level. Check filter air relief valve to ensure o-ring is in 
place and is tightly closed. Check union on front of pump to ensure 
tightness. Check bleeder valve on front of pump to ensure tight-
ness.  

Probable Cause 

Recommended Action 

Jets turned off 

Turn jet face to open jets 

Pump not primed 

Refer to the section in this guide on pump priming. 

Probable Cause 

Recommended Action 

Dirty filter 

Remove filter cartridge and clean. 

Low voltage or incorrect voltage 

Have a 

Licensed Electrician 

check the line voltage 

17 

Summary of Contents for TubLicious 2011



























Reviews: