background image

STATEMENT OF WARRANTY TERMS & CONDITIONS 

 

 

COAIRE’s refrigerated air dryers are warranted to be free of defects in materials and workmanship under proper use, 
installation, and application.  This warranty shall be for a period of 15 months from date of shipment from our factory 
or other stocking facilities or 12 months from date of installation. Proof of installation date will be required.  All dryers 
outside the U.S. and Canada carry a parts only warranty.

 

ALL FREIGHT DAMAGE CLAIMS ARE NOT THE RESPONSIBILITY OF THE MANUFACTURER AND ARE NOT 
COVERED UNDER WARRANTY AS ALL PRODUCTS ARE SHIPPED F.O.B. SHIPPER. 

PLEASE DIRECT ALL FREIGHT CLAIMS TO THE SHIPPER IN QUESTION.

 

MAINTENANCE AND ADJUSTMENTS 

ADJUSTMENTS TO THE HOT GAS AND MAINTENANCE OF FLOAT AND AUTOMATIC DRAINS AND 
CONDENSER COILS ARE CONSIDERED TO BE ROUTINE MAINTENANCE AND THEREFORE NON-
WARRANTABLE ITEMS AND ARE THE SOLE RESPONSIBILITY OF THE END USER. CONSULT THE 
INSTALLATION, OPERATION AND MAINTENANCE MANUAL FOR THE ADJUSTMENT AND MAINTENANCE 
PROCEDURES. 

This warranty does not apply to any unit damaged by accident, modification, misuse, negligence, or misapplication.  
Damage to heat exchangers by exposure to ammonia, any other corrosive substance or sub-freezing environment 
will be considered misuse. 

Any refrigerated dryer part or material found defective will be repaired, replaced or refunded, at the sellers option free 
of charge, provided that COAIRE is notified within the above stated warranty period.  

All returns of allegedly 

defective equipment must have prior written authorization.

  Said authorization may be obtained through our 

refrigerated dryer service department. All refrigerated dryers, parts, materials must be returned 

freight prepaid to

 the 

Manufacturer’s factory within 30 days of return authorization date.  Any shipment returned to the factory collect will be 
refused. 

If an item is found to be warrantable, the repaired item or replacement will be returned normal ground freight prepaid 
within the continental United States and Canada. Expedited shipment costs are the responsibility of the requestor.  

Any replacement part or material is warranted only to the extent of the remaining warranty period of the dryer or to 
the extent as provided by the supplier, whichever is longer. 

Identification Plate 

The identification plate is located on the back of the dryer and shows all the primary data of the machine. Upon 
installation, fill in the table on the previous page with all the data shown on the identification plate. This data should 
always be referred to when calling the manufacturer or distributor.  
The removal or alteration of the identification plate will void the warranty rights.  

DISCLAIMER 

The warranty does not cover any responsibility or liability for direct or indirect damages to persons, or equipment 
caused by improper usage or maintenance, and is limited to manufacturing defects only. Refer to COAIRE Warranty 
policy manual for travel, mileage and special charge considerations. The warranty will be immediately voided if there 
are changes or alterations to the dryer. 

 

WHO TO CONTACT IF YOU HAVE A WARRANTY CLAIM: 

COAIRE 

Technologies, 

Corporation 

  Phone 

 (562) 

463-3935 

                                                                                 

Fax 

 

(562) 463-4928

 

 

All freight damage claims should be filed within 15 working days and should be directed to the carrier.

 

 
 

Summary of Contents for CNCM10



















Reviews: