background image

3

WARNING

  When using two or more suction fittings on a common suction line, suctions must be separated by 

a minimum of 3 ft or they must be located on two different planes (i.e., one on floor and one on the 

wall).

WARNING

  WARNING: DO NOT locate suction outlets on seating areas or on backrests for such seating areas.

NOTICE

  Attention Installer: This manual contains important information about the installation, operation 

and safe use of this product. Before installing this product, read and follow all warning notices and 

instructions which are included. This information should be given to the owner and/or operator of 

this equipment.

WARNING

  To reduce the risk of drowning from hair and body entrapment, install suction fittings with a marked 

flow rate in gallons per minute that exceeds the flow rate of your system by at least 25%.  Always 

use multiple suction outlets.  If the fitting/cover breaks, is damaged, or is missing, shut the system 

down immediately.  Do not use the system until damaged parts have been replaced.

WARNING

  Keep hair and clothing a minimum of 12 inches from all suction fittings and drains at all times. 

Persons with long hair should secure hair to a minimal length or wear swimming cap.  Children 

should never be left unattended at any time in a swimming pool, spa, or bathtub.  Be sure the 

temperature of the water never exceeds the manufacturer’s recommendations.

NOTICE

  To reduce the risk of injury, installation and service should be done by a qualified Pool Service 

Professional, certified electrician or authorized CMP representative.

NOTICE

  NOTE: In the event that one suction outlet is completely blocked, the remaining suction outlet(s) 

serving that system MUST have a flow rating capable of the full flow of the pump(s) for the specific 

suction system.

NOTICE

  Increasing size of the pump may increase flow rate of suction beyond rated safety limits causing 

entrapment or death.

CAUTION

  Hair or body parts blocking the spa or pool suctions may become trapped and held against the 

suction fitting. Entrapment against the suction fittings can result in drowning or other severe injury.  

Never sit on or lean up against suction fittings. Never exceed the maximum allowable flow rate 

stated on the suction fitting. The suction fitting and fasteners should be inspected for damage or 

tampering before use. Missing, broken, or cracked suction fittings shall be replaced. Loose suction 

fittings shall be reattached or replaced before use of this facility.

SAVE THESE INSTRUCTIONS

A. SAFETY INSTRUCTIONS & PRECAUTIONS

IMPORTANT SAFETY INSTRUCTIONS. 

READ AND FOLLOW ALL INSTRUCTIONS

ALWAYS PLUMB AND INSTALL ALL SUCTION FITTINGS ACCORDING TO ALL 

BUILDING CODES THAT APPLY IN YOUR AREA.

Summary of Contents for 25506-33 00 Series











Reviews: