Club Car Precedent 2014, Maintenance And Service Manual

Page: 442 / 548

27
Program Menu
IQ DISPLAY MODULE PROGRAMMER (IQDM-P):
EXCEL SYSTEM WITH ERIC CHARGING
S3 FWD Speed
The s3 fwd speed option allows for adjustability of the SPEED 3 speed setting. From the factory, s3 fwd speed will be
set to one of 4 options: 12.4, 13.2, 14.0 and 14.8 mph (20.0, 21.3, 22.6 and 23.8 km/h, respectively). The default s3
fwd speed is 14.8 mph (23.8 km/h). The s3 fwd speed may be adjusted with the handset from 11.4 to 14.8 mph (18.3
to 23.8 km/h) in 0.1 mph (0.16 km/h) increments. The speed value chosen for s3 fwd speed may also be observed
in the monitor menu. See Vehicle Speeds (IQDM-P Only) on page 26-8.
To fine tune vehicle top speed in normal golf speed range (12.4 to 14.8 mph (20.0 to 23.8 km/h)):
1. Access the program menu, then the speed setting menu with the navigation keys.
2. Select Speed Setting 3 with the change value buttons.
3. Access the program menu and the s3 fwd speed menu with the navigation keys.
4. Use the change value buttons to select desired speed.
Control Mode
The control mode option is used to configure the 1515 controller for different modes of speed control operation.
Four modes are avaiable:
• 0 = Standard: Uses maximum speeds defined by the S1 through S4 Fwd Speed , Rev Speed and Speed Cal
parameters.
• 1 = LIN (Local Interconnect bus) (i.e. Guardian or Visage): Uses maximum speeds assigned to a particular location
or area as defined by the fleet operator; however, these defined speeds can not override maximums set in the S1
through S4 Fwd Speed , Rev Speed and Speed Cal parameters.
• 2 = ES-Protocol (UpLink): Uses maximum speeds assigned to a particular location or area as defined by the fleet
operator; however, these defined speeds can not override previously set values from other control mode options. To
avoid this, after changing the control mode to 2, cycle power to the controller by placing the Tow/Run Switch in the
TOW position for 30 seconds. Then return it to RUN.
• 3 = Deterrent Demo Mode: Uses maximum speeds defined by the deterrent demo setting to demonstrate the
automatic speed control features of Guardian and UpLink. See Deterrent Demo on page 27-4.
Anti-Tamper
The anti-tamper setting defines maximum speed if the Anti-Tamper fault is triggered (e.g. controller is disconnected
from the Guardian or Visage system). These speeds can only be activated if the Control Mode option is set to 1
(Guardian/Visage) and are intended to be a deterrent. Factory default setting is 1.
• 0 = OFF; uses controller configured speed ( S1 through S4 Fwd Speed , Rev Speed and Speed Cal parameters)
even if the Anti-Tamper fault is triggered
• 1 = 2 mph
• 2 = 0 mph
• 3 = 7 mph
Deterrent Demo
The deterrent demo setting defines maximum speed of Control Mode 3.
• 0 = Controller configured speed ( S1 through S4 Fwd Speed , Rev Speed and Speed Cal parameters)
• 1 = 10 mph
• 2 = 7 mph
• 3 = 2 mph
Excel Braking
The excel braking menu item allows the user to turn this function ON or OFF. With it ON, the vehicle maintains the
regen motor braking “feel” of the Excel system. With it OFF, regen motor braking is less aggressive and the vehicle
mimics the “feel” of the IQ system.
Page 27-4 2014 Precedent ® Golf Car Maintenance and Service Manual