Clover CDR 0440 Instruction Manual Download Page 2

Page: 2 / 74

SAFETY PRECAUTIONS

EXPLANATION OF SYMBOLS

WARNING

To reduce a risk of fire or electric shock, do not expose this product to rain or moisture.

CAUTION

Changes or modifications not expressly approved by the manufacturer may void the user’s authority to

operate this equipment.

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the manufacturer.

This symbol is intended to alert the user to the presence of important

operation and maintenance (servicing) instructions in the literature

accompanying the appliance

This symbol is intended to alert the user to the presence of

unprotected “dangerous voltage” within the product’s enclosure that

may be strong enough to cause a risk of electric shock persons

Summary of Contents for CDR 0440











































































Search results

Summary of Contents for CDR 0440

Reviews:

Related manuals for CDR 0440

Brands by name

Popular brands

Clover CDR 0440, Instruction Manual

Search results

Summary of Contents for CDR 0440

Reviews:

Related manuals for CDR 0440

Brands by name

Popular brands