background image

CAM-16 / CAS-16 User Manual v1.0

4

Safety Information

Safety notes regarding installation

• 

Do not expose this unit to water or moisture

• 

Do not expose the unit to naked flames.

• 

Do not block or restrict any air vent

• 

Do not operate the unit in ambient temperatures above 

45°C

• 

The unit has no internal user adjustable parts.  Do not 
remove any panel.

• 

Refer any servicing to qualified service personnel.

• 

Do not replace the power transformer with any other 
type

Conformities

The Cloud CAM-16 and CAS-16 conform to the following 
European EMC Standards:
BS EN 55103-1:2009
BS EN 55103-2:2009
These products have been tested for normal use in 
the commercial and light industrial environment.  If the 
equipment is used in controlled EMC environments, the 

urban outdoors, heavy industrial environments or close 
to railways, transmitters, overhead power lines etc., the 

performance of the units may be degraded.
The Cloud CAM-16 and CAS-16 conform to the following 

European electrical safety standard:
BS EN 60065:2002
The power transformers for the Cloud CAM-16 and  

CAS-16 conform to the following standards:
Power transformer for the UK market: 

 

BS E BABT
Power transformer for the European market: 

E EN60950
Power transformer for USA and Canada: 

C-UL Approved

Power supply information

The CAM-16 and CAS-16 are each shipped with a 15 V AC, 
1.25 A transformer. When powering the CAM-16 and CAS-

16, please ensure that your local AC supply is within the 
range of voltages required by the adaptor BEFORE you plug 

it into the mains. We strongly recommend that you only use 

the supplied transformer.
When the power switches are in the off (‘O’) position, the 

CAM-16 and CAS-16 are disconnected from the power 

transformers.

CAUTION – Servicing

The unit contains no user serviceable parts.  Refer servicing 
to qualified service personnel. Do not perform servicing 
unless you are qualified to do so. Disconnect the power 
cable from the unit before removing the top or bottom 
panel. Only reassemble the unit using bolts/screws identical 
to the original parts.

Summary of Contents for CAM-16













Reviews: