CLIVET CN-XMi D112, Installation And Owner'S Manual

Page: 24 / 68

Table.12-1
ENC1
32:(5B6
00 1 2
FF
3
E
4
D
5
C
6
B
7
A 89
Mainboard codes indication label
Fig.12-1
When V4+ outdoor unit set the code to be found address
automatically, the new V4+ indoor unit do not need to set the
indoor unit address, at this time the V4+ outdoor unit will
distribute different addresses for indoor units automatically.
When V4+ outdoor unit set the code to be found address
non-automatically, all the indoor units must set the system
addresses by remote controller first (For the setting system
address of indoor unit which has two or more main boards, it
has to separate use the display board connected with ten-
core connecting wire to set address for each mainboard,and
the address should be continuous).
The setting of network address is through the
communication of indoor and outdoor units, its address is the
same as the indoor unit system address, and not need to set
separate.
When all indoor units are V4+ series indoor unit, the central
controlling of indoor unit can be finished in the outdoor unit,
and not need to make central control in the indoor unit, the
detail please refers to the V4+ outdoor unit instruction ma-
nual;.
For the previous indoor unit’s central control function, can
use (X, Y, E) terminal to connect and form the central control
group, at this time there is not need to set the network
address, and also can use outside setting network module,
mainboard (CN20) to form network.
Horsepower code
ENC1(system A) Toggle switch
Code
7
Capacity(Horsepower)
11200W(4.0HP)
12500W(5.0HP)
14000W(5.0HP)
For set horsepower
Note: The horsepower
has been set before
leaving the factory,
anyone can’t
modify it except the
maintenance person.
A
6
5
4
3
2
1
0
8
9
2200W(0.8HP)
2800W(1.0HP)
3600W(1.2HP)
4500W(1.5HP)
5600W(2.0HP)
7100W(2.5HP)
8000W(3.0HP)
9000W(3.2HP)
10000W(4.0HP)
16000W(6.0HP)
Base on different purposes to set the switch codes on the main
boards of indoor unit, Once finish the setting, please cut off the
main power, and then switch on the power again. Otherwise,
setting functions could not work.
NOTE
200T1(8.0HP): Please dial switch ENC1 to B for system A
and 8 for system B.
250T1(9.0HP): Please dial switch ENC1 to C for system A
and 9 for system B.
280T1(10.0HP): Please dial switch ENC1 to D for system A
and 9 for system B.
Network Address Setting
ENC1 is used for setting the refrigeration capacity(refer to
Table.12-1 for different indoor unit) of the indoor unit.
Horsepower set
For 71/80/90/112/140/160 models
SW 2 Difinition
z
00 means shutting down the
unit to"stop cold air" at 15
ć
z
z
z
01 means shutting down the
unit to"stop cold air" at 20
ć
10 means shutting down the
unit to"stop cold air" at 24
ć
11 means shutting down the
unit to"stop cold air" at 26
ć
SW 3 Difinition
z
00 means the time of stopping
TERMAL fan is 4 mintues
z
z
z
01 means the time of stopping
TERMAL fan is 8 mintues
10 means the time of stopping
TERMAL fan is 12 mintues
11 means the time of stopping
TERMAL fan is 16 mintues
SW2
ON
1 2
SW2
ON
1 2
SW2
ON
1 2
SW2
ON
1 2
SW3
ON
1 2
SW3
ON
1 2
SW3
ON
1 2
SW3
ON
1 2
Static Pressure set
ENC2
6WDWLFB3UHVVXUH
0 1 2
F
3
E
4
D
5
C
6
B
7
A
89
Fig.12-2
ENC2 is used for setting the static pressure (refer to
Table.12-2 for different indoor unit) of the indoor unit.
0
1
7.1kw 8.0kw 9.0kw 11.2kw 14kw 16kw 20kw 25kw 28kw
0
̚
20Pa
21 ̚ 80Pa
40 ̚ 60Pa
The static pressure in below table is the optimal static pressure
range which means the airflow, noise, and dehumidification are
all in the best state.
Ɣ
81 ̚ 120Pa
121 ̚ 170Pa
171 ̚ 200Pa
61 ̚ 120Pa
121
̚
170Pa
171 ̚ 200Pa
\
2
3
4
ENC2
Table.12-2
&1;0L'' ,QVWDOODWLRQPDQXDO