CLINTON Electronics
6701 Clinton Road
Loves Park, IL 61111
1.800.447.3306 Sales
1.800.549.6393 Support
1.800.633.8712 Fax
www.clintonelectronics.com
Assembly Instructions
4.
Prepare to route wires
Unscrew the cable nut to reveal a plastic nipple inserted in the
nut. Remove this piece and lightly screw on the cable nut to pre-
pare to feed the cables through the hole.
5.
Feed wires through hole
Feed the wires through the cable nuts on the bottom of the
camera, and pull as much slack as needed into the interior of the
camera housing. Tighten the cable nuts, then place the housing
on the arm to prepare for the next step.
6.
Attach Housing to Arm
Attach the housing to the arm of the mount by tightening the
four allen screws located on the underside of the arm.
7.
Adjust Angle
You can adjust the angle of the arm by loosening the single allen
screw located on the underside of the mount’s arm. Gently pull
upward on the base of the housing, and rotate. *NOTE: Loosen
screw just enough to move the housing into position. Loosen-
ing all the way will separate the arm from the housing. Adjust
the arm slowly to protect the housing lid from opening, or the
internal camera from harsh movements.
Cord route option 1:
back of arm
Cord route option 2:
bottom of arm
IRIS JA
CK
OSD EX
TRA
VIDEO OUT
POWER
VIDEO
DC
SET
BNC Input
24V AC Jumper
to Camera
24V AC Input to
Fan/Heater Board
Gently pull upward from
base of housing & rotate
Secure housing lid & internal
camera when adjusting
Plastic Adaptor
Plate Optional
Loosen screw just
enough to adjust
Cord route option 1:
back of arm
Cord route option 2:
bottom of arm
IRIS JA
CK
OSD EX
TRA
VIDEO OUT
POWER
VIDEO
DC
SET
BNC Input
24V AC Jumper
to Camera
24V AC Input to
Fan/Heater Board
Gently pull upward from
base of housing & rotate
Secure housing lid & internal
camera when adjusting
Plastic Adaptor
Plate Optional
Loosen screw just
enough to adjust
8.
Complete setup
Make any final electrical connections to the heater/fan board
and camera. Typical 24V/1A AC connection will run to the heater
board first, then a jumper from the board to the camera.
Test and verify focus, zoom, and other parameters before closing
the case. Once complete, close the housing by tightening the two
allen screws that were loosened in Step 2.
Cord route option 1:
back of arm
Cord route option 2:
bottom of arm
IRIS JA
CK
OSD EX
TRA
VIDEO OUT
POWER
VIDEO
DC
SET
BNC Input
24V AC Jumper
to Camera
24V AC Input to
Fan/Heater Board
Gently pull upward from
base of housing & rotate
Secure housing lid & internal
camera when adjusting
Plastic Adaptor
Plate Optional
Loosen screw just
enough to adjust
Cord route option 1:
back of arm
Cord route option 2:
bottom of arm
IRIS JA
CK
OSD EX
TRA
VIDEO OUT
POWER
VIDEO
DC
SET
BNC Input
24V AC Jumper
to Camera
24V AC Input to
Fan/Heater Board
Gently pull upward from
base of housing & rotate
Secure housing lid & internal
camera when adjusting
Plastic Adaptor
Plate Optional
Loosen screw just
enough to adjust
Cord route option 1:
back of arm
Cord route option 2:
bottom of arm
IRIS JA
CK
OSD EX
TRA
VIDEO OUT
POWER
VIDEO
DC
SET
BNC Input
24V AC Jumper
to Camera
24V AC Input to
Fan/Heater Board
Gently pull upward from
base of housing & rotate
Secure housing lid & internal
camera when adjusting
Plastic Adaptor
Plate Optional
Loosen screw just
enough to adjust
Cord route option 1:
back of arm
Cord route option 2:
bottom of arm
IRIS JA
CK
OSD EX
TRA
VIDEO OUT
POWER
VIDEO
DC
SET
BNC Input
24V AC Jumper
to Camera
24V AC Input to
Fan/Heater Board
Gently pull upward from
base of housing & rotate
Secure housing lid & internal
camera when adjusting
Plastic Adaptor
Plate Optional
Loosen screw just
enough to adjust
Summary of Contents for CE-H13
Page 4: ...v 02 09 12 ...
