background image

CAUTION 

(SEE SECTION 3.3: AUXILIARY OVERFLOW PAN)

In compliance with recognized codes, an auxiliary drain pan must be installed 

under all equipment containing evaporator coils that are located in any area of 

a structure where damage to the building or building contents may occur as a 

result of an overflow of the coil drain pan or a stoppage in the primary conden

-

sate drain piping.

WARNING 

(SEE SECTION 3.6: AIR FILTER)

Do not operate the system without filters. A portion of the dust entrained in 

the air may temporarily lodge in the duct runs and at the supply registers. Any 

circulated dust particles could be heated and charred by contact with the heat-

ing elements. This residue could soil ceilings, walls, drapes, carpets and other 

articles in the building.

Soot damage may occur even with filters in place when certain types of can

-

dles, oil lamps or standing pilots are burned.

WARNING 

The first 36 inches of supply air plenum and ductwork must be constructed 

of sheet metal with no openings, registers or flexible air ducts located in it as 

required by NFPA 90B if an electric heater accessory is installed. If flexible 

supply air ducts are used they may be located only in the vertical walls of a 

rectangular plenum, a minimum of 6 inches from the solid bottom.

WARNING

Because of possible damage 

to equipment or personal injury, 

installation, service, and mainte-

nance should be performed by a 

trained, qualified service person-

nel. Never operate the unit with the 

access panels removed.

WARNING

These instructions are intended as an aid to qualified, licensed service per

-

sonnel for proper installation, adjustment and operation of this unit. Read 

these instructions thoroughly before attempting installation or operation. 

Failure to follow these instructions may result in improper installation, adjust-

ment, service or maintenance possibly resulting in fire, electrical shock, prop

-

erty damage, personal injury or death.

WARNING

If removal of the blower assembly 

is required, all disconnect switches 

supplying power to the equipment 

must  be  de-energized  and  locked 

(if  not  in  sight  of  unit)  so  the  field 

power wires can be safely removed 

from the blower assembly. Failure 

to do so can cause electrical shock 

resulting in personal injury or death.

WARNING

Disconnect all power to unit before 

installing or servicing. More than 

one disconnect switch may be 

required to de-energize the equip-

ment. Hazardous voltage can cause 

severe personal injury or death.

WARNING

Duct leaks can create an unbalanced system and draw pollutants such as dirt, 

dust, fumes and odors into the building causing property damage. Fumes 

and odors from toxic, volatile or flammable chemicals, as well as automobile 

exhaust and carbon monoxide (CO), can be drawn into the occupied space 

through leaking ducts and unbalanced duct systems causing personal injury 

or death (see Figure 1). 

•  If air-moving equipment or ductwork is located in garages or off-garage stor

-

age areas - all joints, seams, and openings in the equipment and duct must 

be sealed to limit the migration of toxic fumes and odors including carbon 

monoxide from migrating into the living space. 

•  If  air-moving  equipment  or  ductwork  is  located  in  spaces  containing  fuel 

burning appliances such as water heaters or boilers – all joints, seams, and 

openings in the equipment and duct must also be sealed to prevent depres-

surization of the space and possible migration of combustion byproducts 

including carbon monoxide into the occupied space. 

WARNING 

(SEE SECTION 3.5: DUCTWORK)

Do not, under any circumstances, connect return ductwork to any other heat 

producing  device  such  as  fireplace  insert,  stove,  etc.  Unauthorized  use  of 

such devices may result in fire, carbon monoxide poisoning, explosion, per

-

sonal injury or property damage.

WARNING 

(SEE SECTION 3.11.3: GROUNDING)

The unit must be permanently grounded. Failure to do so can result in electri-

cal shock causing personal injury or death.

Carbon Monoxide (CO) Poisoning

Can Cause Severe Injury or Death.

Carbon Monoxide from the exhaust of motor 

vehicles and other fuel burning devices can be 

drawn into the living space by the operation of the 

central heating and air conditioning system.

Exhaust from motor vehicles, generators, garden 

tractors, mowers, portable heaters, charcoal and gas 

grills, gasoline powered tools, and outdoor camping 

equipment contains carbon monoxide, a poisonous gas 

that can kill you. You cannot see it, smell it, or taste it.

• 

Do NOT operate an automobile or any engine in a 

garage for more than the few seconds it takes to 

enter or exit the garage.

• 

Do NOT operate any fuel-burning device in an 

enclosed or partly enclosed space, or near  

building windows, doors or air intakes.

The U.S. Consumer Product Safety Commission (CPSC) 

and Health Canada recommend the installation of UL or 

CSA certified Carbon Monoxide Alarm(s) in every home.

  

WARNING

!

!

!

1.0 SAFETY INFORMATION

!

!

!

!

!

!

!

Summary of Contents for HCLA2090CAR









































Reviews: