a. To select another feature in that same column, repeat step 5 within the next 5 seconds (after 5 seconds, 3 chirps mean you are back to the
“Feature Select”
position).
b. To select a different feature column, go to step 4.
c. To exit program mode, turn the ignition off (you’ll hear 3 chirps and the LED will turn off). If driving, just wait 60 seconds and the system
will automatically exit program mode.
If you make an er ror, just turn off the ig ni tion and start again.
Ta ble of User- Selectable Fea tures
Feature Select
1 blank press
2 blank presses
3 blank presses
4 blank presses
1
✱
press
Add a new remote control
NOTE 1
Chirps: off/on
(1/2 chirps)
AutoArming: off/on
NOTE 5 — Other vehicle‘s remote:
arm/disarm (1 then 2 chirps)
2
✱
presses
Personalized Siren Sounds*
NOTE 2
NOT USED
Lock upon AutoArming: off/on
NOTE 6 — Other vehicle‘s remote:
trunk release* (2 chirps)
3
✱
presses
Play Personalized Siren Sounds*:
trigger only/always (1/2 chirps)
Remote valet mode via
button combo
+
✱
: off/on
AutoArming entry delay: off/on
NOTE 6 — Other vehicle‘s remote:
silent arm and disarm (3 chirps)
4
✱
presses
Siren duration: 30 /60/90sec.
(1/2/3 chirps)
AutoStart*: both off/both on/temp
only/battery only (1/2/3/4 chirps)
FACT: off/on
NOTE 6 — Other vehicle‘s remote:
remote engine starting* (4 chirps)
5
✱
presses
AutoLock: off/on
NOT USED
NOT USED
NOT USED
6
✱
presses
AutoUnLock: off/on
Clear all remotes
NOTE 3
NOT USED
NOTE 6 — Other vehicle‘s remote:
window rolldown/venting* (6 chirps)
7
✱
presses
Reset all features (except remotes
and valet code) to factory settings
Set a new secret valet code
NOTE 4
NOT USED
NOTE 6 — Other vehicle‘s remote:
remote valet mode (7 chirps)
* Re quires op tional wir ing or ac ces sory; ask your Clif ford Dealer for de tails.
NOTE 1: Press the
button of the new remote. You’ll hear one chirp. Press the
button again. You’ll hear two
chirps to confirm that the new remote control has been added.
NOTE 2: This feature requires the optional Self-Powered SmartSiren 4. If so equipped, selection of this feature will
cause the system to sound a few seconds of siren sound #1. Press the blank button to turn on this sound or the
✱
button
to turn it off. It will then sound a few seconds of sound #2. Repeat: blank=ON,
✱
=OFF for each of the six sounds.
NOTE 3: You’ll hear two chirps to indicate all remotes have been cleared from memory. You must now add
new/existing remotes with the “Add new remote control” feature and/or the “Other vehicle‘s remote” feature.
NOTE 4: Immediately PRESS THE BLANK BUTTON, THEN enter your new code, wait for the two chirps, then turn off the
ignition (you’ll hear 3 chirps to confirm program mode exit). You MUST now turn the ignition back on and then
re-enter your new code. If the LED flashes on, your new code has been accepted. If the LED does not light, the two
codes did not match and the system has reverted to your previous code.
NOTE 5: Lets you arm/disarm with the remote control of a G4 system on your other vehicle(s). For instance, to set the
✱
button of the other car’s remote to arm and disarm this system, select column 4, row 1, then press the
✱
button of the
other car’s remote (you’ll hear one chirp). Immediately press the
✱
button again (you will hear a 2-chirp
confirmation). The
✱
button of the other vehicle’s remote will now arm/disarm this system.
NOTE 6: The features in this column allow you to control your system with the remote control of a G4 system on your
other vehicle(s). Just select the function you wish, then press the unused button or button combination on the other
remote that you want to use to perform that function on this system (you will then hear a the chirps noted). NOTE: You
must first set a button or button combination on the other car’s remote that will arm/disarm the system (column 4, row
1) before these others will be accepted.
EX AM PLE: Turn on Lock upon AutoArming and turn off Re mote Valet Mode and FACT:
In this example, we’ll change three different features in just one programming session: We’ll turn on the Lock upon AutoArming feature, turn off remote
controlled valet mode and turn off the FACT anti-falsing feature:
1.
Enter program mode
as previously noted (ignition on, enter your valet code, press and hold the
✱
button on the PlainView 2 switch until
you hear a chirp).
2. Since the
Lock upon AutoArming
feature is in column 3, row 2 of the Table, go to column 3 by pressing the blank button on the PlainView 2
switch three times. Wait for the 3-chirp/column 3 confirmation. Then press the
✱
button twice (you’ll hear a chirp each time you press the
✱
button). After a brief pause, you’ll hear 2 chirps to confirm that
Lock upon AutoArming
is now on.
3. Since
FACT
is also in column 3, there is no need to reselect column 3. Therefore, you can go straight to the row selection. Select row 4 by
pressing the
✱
button four times. After a brief pause, you’ll hear one chirp to confirm that
FACT
is now off.
4. You’ll note that the
Remote valet mode
feature is at column 2, row 3. To change to column 2, press the blank button twice, then wait for the
2-chirp/column 2 confirmation. Press the
✱
button three times to select row 3. After a brief pause, you’ll hear one chirp to confirm that the
Remote valet mode
feature is now turned off.
5. To exit the program mode, turn the
ignition off
. You’ll hear 3 chirps to confirm program mode exit.
8
Summary of Contents for CYBER 2
Page 1: ......
