background image

WWW.CLF-LIGHTING.COM

Outdoor IP-rated fixtures

CLF

 products are applied to official classified IP norm levels. For this product the IP rate is IP65 when using the covers for the chassis 

parts. IP65 means according classified norm: shielded against dust and pressurized water from any side.  Typical use for outdoor rated 
stage events with normal weather acceptance. So no heavy rain, because then the water pressure over exceeds the IP norm.

Condensation/moisture inside housing

Because

 of high humidity levels during production condensation can occur inside the housing. This is mostly visible on the coldest parts of 

the fixture, like the front glass or display. To prevent this problem we work with special conditioned areas for outdoor fixtures. Because of 
the breathing air valves it is still possible to get humidity inside the fixture. This will evaporate slowly. Do not put wet fixtures in a flightcase, 
this will help humidity enter the fixture.

Fixtures temperature specification

Make sure the fixture is used within its working temperature range. Outside this range we cannot guarantee correct operation.

Temporary usage:

Stage event equipment is designed with temporary use in mind. Our product purpose is for theatre, festival, (disco) clubs and indoor & 
outdoor concerts.  Long term use is possible but keep in mind that it can bring damage to aging materials and affect the coated surface ( 
i.e. stainless steel). Rubber sealings will be negatively affected after long-term UV exposure and should be checked by qualified service 
technicians over time. 

 

Tighten screws too hard will also affect the IP-rating.

solid object

Moisture

1
2
3
4
5
6
7
8

IP

Ingress 

Protection

6 5

Protected against a solid object greater 

than 50mm such as a hand.

Protected against a solid object greater 

than 12.5mm such as a finger.

Protected against a solid object greater 

than 2.5mm such as a screwdriver.

Protected against a solid object greater 

than 1mm such as a wire.

Dust protected. Limited ingress of 

dust permitted. Will not interfere 

with operation of the equipment. 

Dust tight. No ingress of dust. 

Protected against vertical falling drops of 

water. Limited ingress permitted.

Protected against water splashes from 

all directions. Limited ingress permitted.

Protected against vertical falling drops 

of water with enclosure tilted up to 15 

degrees from the vertical. Limited 

ingress permitted. 

Protected against sprays of water up 

to 60 degrees from the vertical. 

Limited ingress permitted. 

Protected against jets of water. 

Limited ingress permitted.

Protected against powerful jets of water. 

Limited ingress permitted.

Protected against the effects of 

immersion in water between 15cm and 

1m for 30 minutes.

Protected against the effects of 

immersion in water under pressure for 

long periods. 

1
2
3
4
5
6

21.0

Summary of Contents for HERA


























Reviews: