1947471
V1.5
23 June 2022
Instruction Sheet Template - V1.3
–
Updated 20/01/2022
Installation:
The L10 Weatherproof (WP) LED Exit is a 2-part assembly. The LED light source and EXIT decal is housed in a
separate WP enclosure to the WP control gear enclosure. The EXIT enclosure is suitable for temperature
environments of -40°C to +40°C. The remote-control gear enclosure is suitable for temperatures of 0°C to +40°C.
The enclosure bases are attached to the wall using screws installed through the 4 isolated holes. The remote-
control gear enclosure is connected to the EXIT enclosure via a 2-core cable to be supplied by the installer (not
supplied by Clevertronics with the product). To install the 2-part assembly follow these steps.
Remote Control Gear:
1.
Remove the enclosure cover (4 plastic screws at each corner).
2.
Remove the gear tray (4 screws holding the gear tray onto 4 mounting posts).
3.
Determine power entry hole (typically the back) and separately the hole for the 2-core cable (end/side) to
the EXIT enclosure. Drill the two holes.
4.
Position the box base in the mounting position.
5.
Mark the 4 holes for mounting. Install the base using appropriate fixings (not supplied).
6.
Connect the 240VAC supply to the terminal block labelled L, N, E.
7.
Reinstall the gear tray and reinstall the enclosure cover.
EXIT Enclosure:
8.
Remove Cover Screws to remove the Enclosure Cover, Diffuser & Decal followed by the Gear Tray
9.
Determine the cable entry point for the 2-core cable that will come from the remote-control gear.
10. Drill the 2-core cable access hole in the base/end/side of the enclosure (typically the end).
11. Position the box base in the mounting position.
12. Mark the 4 holes for mounting. Install the base using appropriate fixings (not supplied).
13. Reinstall the Gear Tray, Enclosure Cover, Diffuser & Decal
2 core cable connection between the 2 enclosures:
14. During the installation of each component the installer should consider installing the interconnecting cable
between the two components. This will avoid the need to re-visit each enclosure and opening the covers
and remove the gear trays a second time.
15. The 2-core interconnecting cable should use a conductor size of 1.5mm
2
to a maximum distance of 2m.
For lengths greater than 2m, a 2.5mm
2
conductor should be used and the cable should be fire rated to
class WS4X up to a distance of 10m. Please contact Clevertronics for advice on cable lengths and cable
size beyond 10m.
16. Terminate the cable at each end (each enclosure) to the appropriate terminations in the images below
marked LED+ and LED-.
17.
If the CTP capabilities are activated, please affix the CTP status label to a visible surface and Four
Segment Marking on the product will include an ‘’F’’ in third segment block.
18.
(Applicable to -VENT products only
) If the enclosures are installed in a Wall Mounted fashion, please
ensure that the Pressure Equalization Vents are facing downwards upon product installation.
Networking:
When installing the product on a monitored network, (ZONEWORKS, HIVE DATA, DALI) simply insert
the relevant Smart Node PCA.
Dimensions:
Decal Replacement:
Testing:
Once connected to the 240V mains supply, the unit must be allowed to charge the battery for at least 24
hours. Conduct the following tests:
•
For the first test, the emergency lamp must remain illuminated for at least 2 hours after
disconnection from the mains supply.
•
Subsequent tests require the unit to illuminate for at least 90 minutes. The results of all tests are
required to be recorded in a service logbook, which is to be kept on-site at all times. If the unit fails
to remain illuminated for the requisite time, remedial action must be taken to repair the situation
and once completed, the unit must pass a subsequent test. For more specific information, please
refer to the current edition of the AS 2293.3 Standard.
Maintenance:
Lamp Replacement:
•
Use only the lamp(s) recommended on the label
inside the Weatherproof Exit.
•
To replace the lamp bar, remove the screws,
disconnect the signal cable and install the new lamp
bar.
Battery Replacement:
•
Use only the battery recommended on the
label inside the Exit fitting and on this
instruction.
•
Remove the cable ties holding the battery, un-
plug the lead from the PCB and remove the
old battery.
•
Clip the new battery into the holder, route the
DC cable to the PCB and plug the new battery
into the PCB.
•
Secure the battery using suitable cable ties
Trouble Shooting:
Below are a list of common problems and their possible causes.
Fault:
The Green LED Test Switch indicator is not illuminated.
Check: A.C. is connected and is turned on.
Battery is connected
Test Switch for damage.
Fault:
Lamp does not illuminate in emergency mode.
Check: A.C. is connected.
Lamp is correctly inserted.
Battery is connected
Fault:
Lamp illuminates in emergency mode, but only stays on for a short period.
Check:
Battery has been allowed to charge for at least 24 hours.
Battery for damage.
Rated Emergency Lumen Output in accordance with AS2293.1, not applicable
for
–TH (theatre) version (refer to spacing tables for installation positions):
Refer to the Technical Label for classification information.
2-core cable termination point
–
for
connection of the 2 enclosures
2-core cable
termination point
–
for connection of
4 x mounting
ports
Same
240V AC
Termination
point L, N,
E
Step 1 - Remove
Enclosure Cover Screws
Step 2 - Remove the
Diffuser from the Cover
Step 3
–
Remove/Replace the
required Decal
NOTE:
Once Decals have been replaced, repeat ‘Decal Replacement’ steps in the reverse re-install the Cover,
Diffuser & Decal
