![background image](http://html1.mh-extra.com/html/clevertronics/l10-lwfled-2iprem-series/l10-lwfled-2iprem-series_installation-and-maintenance-instruction-manual_2623537002.webp)
1949327
V1.0
21 January 2022
Instruction Sheet Template - V1.3
–
Updated 20/01/2022
Installation:
The L10 Weatherproof Supalite (LWFLED-IPREM) is Surface Mounted. The Control gear and Lamp
Heads are housed in weatherproof enclosures. The enclosures are attached to the wall using screws
installed through the 4 isolated holes. Please follow the steps below to install the Weatherproof fitting.
Control Gear
•
Remove the Control Gear cover.
•
Remove the gear tray.
•
Determine power entry.
•
Drill power access hole in the box base.
•
Position the box base in the mounting position.
•
Mark the 4 holes for mounting. Install the base using appropriate fixings (not supplied).
•
Connect the 240VAC supply to the terminal block on the Gear Tray.
•
Reinstall the gear tray.
Remote Lamps
•
Remove the enclosure cover.
•
Determine cable entry point for LED cable from the Control Gear.
•
Drill appropriate hole and install an appropriate cable gland.
•
Position the box and mark out the mounting holes. Install the box using appropriate fixings.
•
Route and connect the LED drive cables from the Control Gear (LED+, LED-) using appropriate
weatherproof glands between the Control Gear and the Lamp Heads to maintain the IP65 rating.
If the CTP capabilities are activated, please affix the CTP status label to a visible surface and Four
Segment Marking on the p
roduct will include an ‘’F’’ in third segment block.
Networking:
When installing the product on a monitored network, (ZONEWORKS, DATA, DALI) simply insert the
relevant Smart Node PCA.
Dimensions:
Testing:
When the Supalite unit is connected to the un-switched active, it must be allowed to charge the battery
for at least 24 hours. The emergency lamp only illuminates during a power fail. Conduct the following
tests:
•
The emergency lamps must illuminate for at least 2 hours after disconnection from the mains. The
results of all tests are required to be recorded in a service logbook, which is to be kept on-site at all
times. If the unit fails to illuminate for the requisite time, remedial action must be taken to repair the
situation and once completed, the unit must pass a subsequent test.
•
Press and hold Test Button or switch Off Mains Supply, check that the emergency lamps are On.
•
Release the Test Button or Switch On Mains Supply, check that the emergency lamps are Off
(Non-maintained operation).
Trouble Shooting:
Below are a list of common problems and their possible causes.
Fault:
The Green LED Test Switch indicator is not illuminated.
Check: A.C. is connected and is turned on.
Battery is connected
Test Switch for damage.
Fault:
Lamp does not illuminate in emergency mode.
Check: A.C. is connected.
Lamp is correctly inserted.
Battery is connected
Fault:
Lamp illuminates in emergency mode, but only stays on for a short period.
Check:
Battery has been allowed to charge for at least 24 hours.
Battery for damage.
Rated Emergency Lumen Output in accordance with AS2293.1, not applicable
for
–TH (theatre) version (refer to spacing tables for installation positions):
Refer to the Technical Label for classification information.
Caution:
On many building sites, power circuits may be cut off in an uncontrolled and repetitive basis during
construction. As a result, any Exit & Emergency Units, on these circuits, will have their batteries
discharged or “cycled”. The battery in this fitting has been selected to give excellent long-life
performance in a controlled AS2293 testing environment. Excessive battery cycling will reduce through-
life performance and may lead to premature battery failure. Battery warranty claims, as a result of such
abuse, are specifically EXCLUDED from Clevertronics warranty terms.
Warranty:
For Product Warranty information and Terms and Conditions of Sales please refer to our website
http://clevertronics.com.au/terms-conditions-sale-australia-nz/