1943071
V1.4
28 June 2022
Instruction Sheet Template - V1.3
–
Updated 20/01/2022
Important:
It is illegal for anyone, except for a licensed electrician to install or maintain this product. Before installation,
ensure that the electricity supply has been switched off and isolated. Installation must be carried out in
accordance with the relevant Australian and International Standards.
Installation:
The L10 Swingblade LED Exit (LSBLED) is a surface mount (wall or ceiling) fitting. The LSBLED can be
attached directly to any solid surface, or to a ceiling tile using the integrated mounting bracket. Please
follow the steps below to install the LSBLED Exit:
•
Remove the mounting bracket from the fitting.
•
Using the bracket as a guide, mark 2 holes for mounting screws. Then install the bracket.
•
Connect the 240VAC supply.
•
Insert the LSBLED body into the bracket and slide to lock into position.
•
If the CTP capabilities are activated, please affix the CTP status label to a visible surface and Four
Segment Marking on the product will incl
ude an ‘’F’’ in third segment block.
NOTE: If product is suspended below the ceiling or mounted on a metal surface the Swingblade
bracket cover plate accessory (S/N:2740100) is required to cover the mains terminals.
Networking:
When installing the product on a monitored network, (ZONEWORKS, DATA, DALI) simply insert the
relevant Smart Node PCA.
Dimensions:
Changing Diffuser Decals: (Not applicable to LCSBLED and
–TH
options)
The Swingblade Exit uses Clevertronics patented “Tamper proof” Exit legend cover and comes complete with
spare legend inserts to enable straight on, left or right arrow as well as SS/DS combinations.
The tamper proof cover is held in place by 3 locking tabs recessed in the top edge of the diffuser. Use a tool to
disengage and push the locking tabs through to release the cover and remove the insert, replacing it with the
desired one.
To re-install the clear cover, first engage the three small lugs on the bottom of the cover into the respective
recesses in the diffuser. Once you are sure the lugs are located, carefully push the 3 locking tabs back in to
complete the process.
Testing:
Once connected to the 240V mains supply, the unit must be allowed to charge the battery for at least 24 hours.
Conduct the following tests:
•
For the first test, the emergency lamp must remain illuminated for at least 2 hours after disconnection
from the mains supply.
•
Subsequent tests require the unit to illuminate for at least 90 minutes. The results of all tests are required
to be recorded in a service logbook, which is to be kept on-site at all times. If the unit fails to remain
illuminated for the requisite time, remedial action must be taken to repair the situation and once
completed, the unit must pass a subsequent test. For more specific information, please refer to the
current edition of the AS 2293.3 Standard.
Swingblade Maintenance:
Battery/Lamp Replacement:
•
Prise off the plastic end caps from ends using
a terminal screwdriver
•
Disconnect the lamp lead from the PCB and
slide out the LED light bar.
•
Reinsert new LED light bar, reconnect the
lamp lead and replace the plastic end cap.
•
Remove the central screw connecting the two
earth leads to the earth bar. This screw holds
the equipment tray in place.
•
Slide the gear tray out from the test
switch/light bar end, unplugging the AC
connector once it is revealed.
•
Unplug the battery lead then bend back the
metal tabs securing the battery pack. Remove
the battery and replace with the changeover
battery pack.
Re-assemble the fitting reversing the above
procedure. It is important that the screw securing
the two earth leads is re-installed and tightened
correctly.
Trouble Shooting:
Below are a list of common problems and their
possible causes.
Fault:
The Green LED Test Switch
indicator is not illuminated.
Check: A.C. is connected and is turned on.
Battery is connected
Test Switch for damage.
Fault:
Lamp does not illuminate in
emergency mode.
Check: A.C. is connected.
Lamp is correctly inserted.
Battery is connected
Fault:
Lamp illuminates in emergency
mode, but only stays on for a short
period.
Check:
Battery has been allowed to charge for
at least 24 hours.
Battery for damage.
Rated Emergency Lumen Output in accordance with AS2293.1, not applicable
for
–TH (theatre) version (refer to spacing tables for installation positions):
Refer to the Technical Label for classification information.
Caution:
On many building sites, power circuits may be cut off in an uncontrolled and repetitive basis during
construction. As a result, any Exit & Emergency Units, on these circuits, will have their batteries
discharged or “cycled”. The battery in this fitting has been selected to give excellent long-life
performance in a controlled AS2293 testing environment. Excessive battery cycling will reduce through-
life performance and may lead to premature battery failure. Battery warranty claims, as a result of such
abuse, are specifically EXCLUDED from Clevertronics warranty terms.
Warranty:
For Product Warranty information and Terms and Conditions of Sales please refer to our website
http://clevertronics.com.au/terms-conditions-sale-australia-nz/
Press locking tab and slide to remove from
bracket
Mounting Bracket
Locking
Tab
Locking
Tabs
