background image

CLEARSPAN

 POLY BUILDINGS

12

Revision date: 05.19.09

NOTE:

 Verify that the bolt heads are to the outside of 

the shelter and tighten the nuts.

3.  Install the remaining struts and tighten all band clamp 

bolts.

4.  Secure each band clamp to the purlin and rafter using 

a Tek screw for each connection.

5.  Return to each purlin joint and secure using a Tek 

screw.

90°

Strut

FRAME ASSEMBLY (CONTINUED)

SQUARE THE ASSEMBLED FRAME

Gather the parts: Measuring tape and Tek screws 

Complete these steps:
1.  Square the frame by measuring diagonally corner-to-

corner and align all rafters as shown below.

2.  Verify that the width of each rafter is 20' center-to- 

center. The frame is square when the two diagonal 

measurements are the same. See previous diagram.

3.  Continue by anchoring the frame.

ANCHOR THE FRAME

Once the frame is anchored properly, continue with these 

instructions.

 

WARNING

: Securing the rafter mounting feet (if 

equipped) to baseboards set on the site is not a 

substitute for properly anchoring the shelter. You must 

anchor the shelter as described in the MUST READ 

document.

FAILING TO PROPERLY ANCHOR THE SHELTER

WILL RESULT IN DAMAGE TO THE SHELTER AND

MAY CAUSE PERSONAL INJURY. 

READ THE MUST READ DOCUMENT TO PROPERLY

ANCHOR THE SHELTER.

After anchoring the frame, check the frame for rough 

edges as described in the following procedure.

2.  Remove the bolts and attach a strut between the band 

clamp on the purlin and the band clamp on the end 

rafter. Position the strut so that it forms a triangle as 

shown below.

 Actual strut and position may vary.

 

FINAL FRAME CHECK

1.  Return to the frame connections and verify that all bolts 

are tight.

2.  Verify that each purlin splice is secured with a Tek 

screw.

3.  Verify that each purlin is secured to the end clamp and 

cross connector and that each cross connector and 

end clamp is secured to the rafter. See diagram below.

4.  Inspect the frame for sharp areas that could damage 

the cover. If found, file smooth and cover with layers of 

duct tape to protect the cover.

5.  Verify that all bolts are positioned with the heads to the 

outside of the frame. Tape the bolts and rafter joints 

before

 installing the cover.

6.  Continue by installing the main cover.

Cross Connector 

to Rafter Tek 

Screw

Purlin to Cross 

Connector Tek 

Screw

Rafter

Purlin

ATTENTION:

 Rafter 

shown may differ 

from the actual 

rafter. Steps to 

secure the purlin to 

the connector and 

the connector to the 

rafter are the same. 

Position the Tek 

screws so they will 

not touch the cover 

once it is installed.

FRAME TOP VIEW

Summary of Contents for 108294F


























Reviews: