background image

15

Limited Warranty & Technical Support

ClearPix warrants to the original consumer purchaser, that this
product will be free of defects in material and workmanship for a
period of 3 years from date of purchase. The manufacturer’s liability
hereunder is limited to replacement of the product, repair of the
product or replacement of the product with repaired product at the
discretion of the manufacturer. This warranty is void if the product has
been damaged by accident, unreasonable use, neglect, tampering or
other causes not arising from defects in material or workmanship. This
warranty extends to the original consumer purchaser of the product
only. 

CLEARPIX DISCLAIMS ALL OTHER WARRANTIES EXPRESSED
OR IMPLIED INCLUDING, WITHOUT LIMITATION, ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, EXCEPT TO THE EXTENT THAT ANY
WARRANTIES IMPLIED BY LAW CANNOT BE VALIDLY WAIVED. 

No oral or written information, advice or representation provided by
ClearPix, its distributors, dealers, agents or employees shall create
another warranty or modify this warranty. This warranty states
ClearPix’s entire liability and your exclusive remedy against ClearPix
for any failure of this product to operate properly. 

In no event shall ClearPix be liable for any indirect, incidental, special,
consequential, exemplary, or punitive damages whatsoever (including
but not limited to, damages for loss of profits or confidential or other
information, for business interruption, for personal injury, for loss of
privacy, for failure to meet any duty including of good faith or of
reasonable care, for negligence, and for any other pecuniary or other
loss whatsoever) arising from the use of or inability to use the product,
even if advised of the possibility of such damages. Since some
jurisdictions do not allow the above limitation of liability, such limitation
may not apply to you. 

This Limited Warranty gives you specific legal rights and you may also
have other rights which vary from jurisdiction to jurisdiction.

Warranty service and technical support can be obtained
by contacting ClearPix Technical Support by phone at
1.866.883.0203 or via email at [email protected].

Summary of Contents for CPX-ENC40-H2
























Reviews: