manualshive.com logo in svg

Clean Water Systems Birm 7800, Installation & Start?Up Manual

Share
Download
Clean Water Systems Birm 7800 Installation & Start?Up Manual Download Page 2

 Pro-OX 7800 Installation & Startup Guide 

Page 1            

www.cleanwaterstore.com 

    

Rev 120214 

Table of

 

Contents 

Packing List .................................................................................................................................................... 2 

Pre-Installation .............................................................................................................................................. 3 

Best Practices for Piping & Drain Installation ............................................................................................... 3 

How Your Birm Filter System Works ............................................................................................................. 4 

Fig. 1: Birm Filter Tank Diagram ....................................................................................................... 4 

Fig. 2: Typical Installation of a Birm Filter System ........................................................................... 5 

Assembly and Installation Instructions ......................................................................................................... 6 

Fig. 3: Media Funnel Use .................................................................................................................. 6 

Fig. 4: CWS 7800 Bypass and Pipe Connectors ................................................................................ 7 

Fig. 5: CWS 7800 Bypass Knobs ........................................................................................................ 8 

Programming Instructions ............................................................................................................................ 9 

Starting The Initial Backwash ........................................................................................................................ 9 

Maintaining Your Birm Filter System .......................................................................................................... 11 

Troubleshooting the Birm 7800 Iron Filter System ..................................................................................... 11 

What to Do If Your Filter Tank Does Not Sit Level on the Floor .................................................... 11 

How to Remove the Red Clips from the 7800 Control Valves without Breaking Them ............................. 12 

 

Summary of Contents for Birm 7800














Reviews:

No comments

Brands by name

Popular brands

Load more brands