background image

TAMBORA BATTEN

6

Switching on the projector - Fig. 7

Switch-on the fixture. The projector starts resetting the effects. At the same time, the following information scrolls on the display:

        

                                Model                                      Firmware                             Dmx Address xxx                 System errors

                                                         Tambora                                 Version X.X.X                                                                      .........................
                                                         Batten                                     Date - Hour                                                                        .........................

On conclusion of resetting in case of absence of the dmx signal, Tilt move to the “Home” position (Tilt 128 bit). The control panel (Fig. 7) has a display
and buttons for the complete programming and management of the projector menu. The display can be in one of two conditions: rest status and setting
status. When it is in the rest status, the display shows the projector’s DMX address. 

During menu setting status, after a wait time (about 30 seconds) without any key having been pressed, the display automatically returns to rest status.
It should be noted than when this condition occurs, any possible value that has been modified but not yet confirmed with the

F

key will be cancelled.

1

Dmx Address

Warning Message

 

 

7

3.5 Switching on the fixture and basic SetUp

28

28

Reversal of the display - Fig. 8

To activate this function, press UP 

B

and DOWN 

C

keys simultaneously while the display is in the rest mode. This status will be memorised and

maintained even for the next time it will be switched on.  To return to the initial state, repeat the operation all over again.

Setting the projector starting address

On each projector, the starting address must be set for the control signal (addresses from 1 to 512). 

The address can also be set with the projector switched off.

8

Functions of the buttons - Using the menu

Confirms  the  displayed  value,  or  activates  the  displayed  function,  or  enters  the  successive
menu. 

Decreases the value displayed (with auto-repetitions) or passes to the next item in the menu.

Increases the value displayed (with auto-repetitions) or passes to the previous item in a menu.

Return to the top level

Enters the successive menu

F
C

DOWN

B

UP

D

LEFT

E

RIGHT

Summary of Contents for CL3010













Reviews: