ChApter 2 GettiNG stArted
| 6
ChApter 2 GettiNG stArted
| 7
3
Strike .the .pad .or .drum .that .causes .the .un-
wanted .triggers .and .raise .the .Inp .Thres .value .
with .the .dial .until .the .Nord .Drum .channel .
stops .triggering .
4
Strike .the .pad .that .should .trigger .the .Nord .
Drum .to .verify .that .the .new .Inp .Thres .setting .
has .not .changed .the .desired .response . .
Play the Demo
1
Press .the .Program, .Channel .Select .and .Trig .
buttons .simultaneously .to .start .the .Demo .
playback . .
2
Turn .the .Dial .while .the .demo .is .playing .to .
listen .to .the .various .sounds .in .the .Factory .
soundbank . .
3
Press .Shift/Exit .to .stop .the .playback .
MIDI Channel Learn
If .you .wish .to .control .the .Nord .Drum .with .a .MIDI .
controller, .the .MIDI .channel .and .the .notes .that .this .
controller .transmits .can .be .automatically .assigned .
by .the .Nord .Drum .to .trigger .the .four .channels .
1
Connect .a .MIDI .pad .or .other .MIDI .controller .
to .the .MIDI .Input .on .the .Nord .Drum . .
2
Press .Shift .and .the .MIDI .Ch .button .and .scroll .
with .the .Dial .until .you .reach .“L .r .n” . .
E
M
TheELEDEaboveEtheEMIDIEChEbuttonEwillEflashE
toEindicateEthatEyourEareEeditingESystemE
parameters.
3
Transmit .a .MIDI .note .or .other .message .from .
the .MIDI .controller . .The .incoming .channel .will .
be .displayed .in .the .LED . .
E
M
TheENordEDrumEcanEonlyEreceiveEonEoneEMIDIE
channelEatEaEtime.
MIDI Note Learn
1
Connect .a .MIDI .pad .or .other .MIDI .controller .
to .the .MIDI .Input .on .the .Nord .Drum . .
2
Press .the .Channel .Select .button .on .the .Nord .
Drum .to .select .one .of .the .channels . .
3
Hold .Shift .and .press .the .MIDI .Note .button . .
Turn .the .dial .until .you .reach .the .setting .after .
127, .“L .r .n” . .
4
Strike .the .pad .on .the .MIDI .unit .that .you .
wish .to .assign .to .the .selected .Nord .Drum .
channel . .
The .note .number .that .the .MIDI .pad .transmit-
ted .will .be .assigned .to .this .Nord .Drum .chan-
nel .and .will .be .shown .in .the .display .
5
Repeat .steps .2, .3 .and .4 .to .assign .the .other .
three .channels .to .the .additional .MIDI .note .
numbers .that .the .MIDI .unit .transmits . .
6
Press .the .Program .button .to .Exit .the .System .
edit .mode .
Four Modes
When .the .display .shows .the .letter .P .followed .by .
a .number, .this .is .the .Program .Mode . .Turn .the .Dial .
to .select .any .of .the .99 .programs . .
When .one .of .the .red .LEDs .in .the .two .rows .below .
the .LED .is .lit .and .the .display .shows .shows .one .or .
two .set .s .of .numbers, .this .is .the .Edit .Mode .where .
you .can .change .the .settings .of .the .selected .
parameter .with .the .Dial . .
