Classeq CST Engineer'S Manual Download Page 46

Page: 46 / 48

ENGINEERS MANUAL

CST MACHINES AND DRYER UNIT

Drawn up: 05/10/2018

Document number : 30008893

Page 46 of 48

Revision: C

16.

Trouble shooting

Machine does not fill:



Check water supply is turned ON.



Check water supply hose is not trapped or kinked.



Check that the machine is switched ON.



Check that door is closed.



Check table end switch has not been activated.



Check there is no obstruction around the drive plate or cassette.



Check that the air pressure switches are switched correctly (see wiring diagram)



Check solenoid valve and rinse pump are getting powered up.

II.

Cycle does not start:



Check that the machine is switched ON.



Check wash tank is full.



Check that the error lamp is not illuminated.



Check basket arm rod touching the basket.



Check water supply is turned ON.



Check water supply hose is not trapped or kinked.



Check that the rinse boiler is full.



Check that breaker 4 and 5 are both on.

III.

Machine fills slowly:



Check water supply tap is fully open.



Check water supply hose is not trapped or kinked.



Check water supply pressure and remove any pressure regulator or reducer.



Check and clean rinse jets

(located on the rinse arms within the machine).



Check drain plug securely fitted and sealing.



Check the correct flow restrictors are fitted:

Purple (4l/min) in rinse hose

Orange (8l/min) in solenoid

IV.

Machine not heating:



Check machine is ON.



Ensure enough time has been allowed for machine to reach correct temperatures.



Check that the machine is full of water.



Check that breaker 3 is ON.



Check breaker 1 and 2 are on as relivent.

Machine not draining:



Check and clean all filters within the machine.



Check that the drain is not clogged / blocked / kinked.



Check waste hight is below the base of the machine.

VI.

Poor wash results:



Check and replenish chemicals.



Ensure chemical dosing is corect.



Check and clean wash and rinse jets on the wash and rinse arm assemblies.



Clean filters within machine and check that they are fitted correctly.



Check water supply is ON and fully open.



Rinse dishes of food debris before placing into the dishwasher.

Summary of Contents for CST

















































Search results

Summary of Contents for CST

Reviews:

Related manuals for CST

Brands by name

Popular brands

Classeq CST, Engineer'S Manual

Search results

Summary of Contents for CST

Reviews:

Related manuals for CST

Brands by name

Popular brands