background image

TROUBLE SHOOTING

PARTS & SERVICE TEL:  020 8988 7400

PARTS & SERVICE FAX:  020 8558 3622

or    e-mail as follows:

PARTS:   [email protected]

SERVICE:    [email protected]

For Spare Parts and Service, please contact your nearest dealer, or CLARKE International, on

one of the following numbers.

 SPARE PARTS AND SERVICE

Gas leak

Gas leak

Igniter electrode or piezo wire not connected

Broken electrode or piezo wire

Faulty piezo igniter

Electronic ignition is wet

Gas supply not turned on

Control knob not in PILOT position

Low gas pressure

Faulty Regulator

Crimped pilot gas line

Air in gas line

Thermocouple not hot enough

Connections not secure

Faulty thermocouple

Faulty valve

Windy conditions

Low gas pressure

Blocked orifice

Faulty valve

Low gas pressure

Connections not secure

Faulty valve

Faulty Regulator

Windy conditions

Incorrect gas supply or pressure

Blocked orifice

Faulty valve

Faulty Regulator

High altitude

Gas odour during setup

Gas odour before first ignition

When piezo igniter button is
pressed, there is no spark at
pilot electrode.

When igniter button is pressed,
there is spark at the pilot
electrode, but no pilot ignition

Pilot lights but does not stay lit

Delayed ignition

Burner lights but does not stay lit

Incorrect Burner flame

Check all gas connections

Check all gas connections

Reconnect igniter electrode or wire**

Replace broken electrode or wire**

Replace piezo igniter**

Keep ignition system dry

Turn on gas supply

Follow Operational Instructions

Check gas supply pressure

Replace regulator

Replace pilot gas line**

Pressing control knob in for 1-2 minutes or
until you smell gas.

Hold down control knob longer in pilot
position.

Tighten connections

Replace thermocouple**

Replace valve**

Shield from wind

Check gas supply pressure

Check orifice opening**

Replace valve**

Check gas supply pressure

Tighten connections

Replace valve**

Replace regulator

Shield from wind

Check gas supply pressure

Check orifice opening**

Replace valve**

Replace regulator

Adjust orifice size for altitude**

PROBLEM

POSSIBLE CAUSE

REMEDY

** Consult your Clarke dealer

11

Summary of Contents for PHT3













Reviews: