Clarke DEVIL 371PC Operating & Maintenance Instructions Download Page 5

5

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

sharp edges or moving parts. Damaged or tangled cables increase the risk 
of electric shock.

3. Keep the power cable well away from machines and ensure an adequate 

electrical supply is close at hand so that the operation is not restricted by 
the length of the cable.

4. DO NOT use this product with an extension cable.

5. ALWAYS disconnect from the power supply before moving the heater or 

performing any cleaning or maintenance tasks.

6. Inspect the mains cable regularly for signs of damage. DO NOT use if it is 

damaged, and ALWAYS keep it away from the source of heat.

7. Check the heater for damage before use. DO NOT use if the heater tubes 

are damaged or broken. Any damage should be properly repaired or the 
part replaced. If in doubt, 

DO NOT

 use. Consult your local Clarke dealer.

SERVICE & REPAIRS

1. If necessary, have your heater repaired by a qualified person using 

identical replacement parts. This will ensure that the safety of the 
appliance is maintained.

Please keep these instructions in a safe place for future reference.

ENVIRONMENTAL RECYCLING POLICY

Through purchase of this product, the customer is taking on the obligation to 
deal with the WEEE in accordance with the WEEE regulations in relation to the 
treatment, recycling & recovery and environmentally sound disposal of the 
WEEE.

In effect, this means that this product must not be disposed of with general 
household waste. It must be disposed of according to the laws governing 
Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal 
facility.

Summary of Contents for DEVIL 371PC

















Reviews: