Clarke CONTRACTOR CON1450WC Operation And Maintenance Instructions Download | Manualshive

Page: 9 / 16

background image

9

FITTING THE DUST EXTRACTION ASSEMBLY

Attach the dust extraction assembly
to the wall chaser.

• Insert the assembly (1) into the

extraction port (2) and rotate
slightly clockwise to lock into
place.

• Remove the collar (4) and slide

it over the vacuum cleaner
hose.

• Push the hose onto the dust

extraction tube (3).

• Secure in place by tightening up the collar (4).

FITTING THE ATTACHABLE HANDLE

Screw the handle (5) into the hole (6)
shown on the wall chaser.

«
...
7
8
9
10
11
...
»

Summary of Contents for CONTRACTOR CON1450WC

















Reviews:

No comments

Related manuals for CONTRACTOR CON1450WC

Brand: Walmag Pages: 20

Brand: Balcrank Pages: 8

Brand: jbc Pages: 12

Brand: Makita Pages: 80

Brand: Tarmo Pages: 3

Brand: Greenlee Pages: 12

Brand: Major tech Pages: 16

Brand: Hilti Pages: 32

PSBEN 3012C/LCD

Brand: Pulsar Pages: 44

Brand: Southwire Pages: 19

Brand: Greencut Pages: 20

Brand: Stanley Pages: 128

Sorensen XG 100-15

Brand: Ametek Pages: 399

rescue pac 1600

Brand: SIP Pages: 6

Brand: Würth Pages: 8

Brand: Gallagher Pages: 76

Brand: RIDGID Pages: 40

KF**-CRG2-1.D Series

Brand: Pepperl+Fuchs Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands