Clarke CAT117 Operating & Maintenance Instructions Download Page 14

14

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

Any major servicing and repairs should be carried out by your local CLARKE 
dealer or a qualified service technician.

STORAGE

If the tool is to be stored, or is idle for longer than 24 hours, run a few drops of 
CLARKE air line oil into the air inlet, and run the tool for 5 seconds in order to 
lubricate the internal parts. Store the tool safely in its box in a dry, secure 
place.

When not in use, disconnect from the air supply, clean and store in a safe, dry 
place. When storing, replace the blanking plug to the airline inlet.

Avoid storing the tool where the temperature is below 0

o

C.

ACCESSORIES

A wide range of accessories is available including filter/regulators, lubricators, 
high-pressure hoses (5 to 50 metres) etc. 

**CLARKE Air Line Oil (part no. 3050825) is available from your CLARKE dealer.

Contact your CLARKE dealer for further information or the CLARKE 
International Service Department.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12 
months from the date of purchase. Please keep your receipt which will be 
required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or 
tampered with in any way, or not used for the purpose for which it was 
intended.

Faulty goods should be returned to their place of purchase, no product can 
be returned to us without prior permission.

This guarantee does not affect your statutory rights.

Summary of Contents for CAT117

















Reviews: