background image

10

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

gum solvent oil, or failing this, the tool should be disassembled, thoroughly 
cleaned, dried and reassembled. This is better left to your Clarke dealer.

3. After extensive use, remove the 

inlet screen filter and flush out the 
mechanism with gum solvent oil or 
an equal mixture of Clarke air-line 
oil and paraffin. Allow to dry 
before use.

4. f the tool runs erratically or 

becomes inefficient, and the air 
supply is of good quality, it may be 
necessary to dismantle the air 
motor and replace worn or 
damaged parts. You may prefer to take the tool to your Clarke dealer if 
internal maintenance is required.

PERFORMANCE

Please note that factors other than the tool may effect its operation and 
efficiency such as reduced compressor output, excessive drain on the airline, 
moisture or restrictions in the air-line, or the use of connectors of improper size 
or poor condition which will reduce air supply.

**Clarke Air Line Oil (part no. 3050825) is available from your Clarke dealer.

Your Clarke air tool has been designed to give long and trouble free service. If, 
however, having followed the instructions in this booklet carefully, you 
encounter problems, take the unit to your local Clarke dealer.

STORAGE

When not in use, disconnect from air supply, clean & store in a safe, dry place. 
If the tool is to be stored, or is idle for longer than 24 hours, run a few drops of 
Clarke air line oil into the air inlet, and run the tool for 5 seconds in order to 
lubricate the internal parts.

ACCESSORIES

A wide range of accessories is available including filter/regulators, lubricators, 
high-pressure hoses (5 to 50 metres) etc. Contact your Clarke dealer for further 
information.

ABRASIVE BELTS

Replacement abrasive belts are available from your CLARKE dealer:

60 grit (pack of 5)

Part no. 3110751

80 grit (pack of 5)

Part no. 3110752

Summary of Contents for Air CAT70

















Reviews: