Clarke 8877106 Operation & Maintenance Instructions Manual Download Page 21

Page: 21 / 24

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

TROUBLESHOOTING

If this does not solve your problem, please contact the CLARKE service
department.

PROBLEM

CAUSE

SOLUTION

The generator
fails to start

Engine switch is off

Set the engine switch to ‘on’

Not enough oil in the
generator

Add more oil, See pages 9-10.

No fuel

Add more fuel, See page 10.

Spark plug not working
correctly

Change the spark plug, See
page 19.

The generator
fails to generate
electricity

The device you are trying
to power is faulty

Make sure the device you want
to power is working properly.

The overload indicator is
on

Remove the appliance
immediately, do not connect
any appliance that requires
more than 800W.

(DC supply only) The DC
Overload protector has
activated.

Press the reset button. See page
15.

The generator is
difficult to start

The air filter is dirty

Clean the air filter. See page 18.

Summary of Contents for 8877106

























Search results

Summary of Contents for 8877106

Reviews:

Related manuals for 8877106

Brands by name

Popular brands

Clarke 8877106, Operation & Maintenance Instructions Manual

Search results

Summary of Contents for 8877106

Reviews:

Related manuals for 8877106

Brands by name

Popular brands