manualshive.com logo in svg

Clarke 8877105, Operation & Maintenance Instructions Manual, Page: 23 / 28

Share
Download
Clarke 8877105 Operation & Maintenance Instructions Manual Download Page 23

23

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

TROUBLESHOOTING

PROBLEM

CAUSE

SOLUTION

The generator 
fails to start

Engine switch is off.

Set the engine switch to ‘on’.

Not enough oil in the 
generator.

Add more oil, See page 11.

No fuel

Add more fuel, See page 12

Spark plug not working 
correctly.

Change the spark plug, See 
page 21.

The generator 
fails to generate 
electricity

The device you are trying 
to power is faulty.

Make sure the device you want 
to power is working properly.

The overload indicator is 
on.

Remove the appliance 
immediately, do not connect 
any appliance that requires 
more than 800W.

(DC supply only) The DC 
Overload protector has 
activated.

Press the reset button. See 
page 17.

The generator is 
difficult to start

The air filter is dirty.

Clean the air filter. See page 20

If this does not solve your problem, please contact the CLARKE service 
department. see below.

Summary of Contents for 8877105





























Reviews:

No comments