manualshive.com logo in svg

Clarke 6267017, Operation & Maintenance Instructions Manual, Page: 9 / 20

Share
Download
Clarke 6267017 Operation & Maintenance Instructions Manual Download Page 9

9

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

THE CHARGING PROCESS

STEP 1: ANALYSING 1

: Checks if the battery has connected with the charger.

STEP 2: DESULPHATION

: If battery voltage is too low, the program automatically 

generates a pulsing current to remove sulphate.

STEP 3: SOFT START

: Charges with gradually increasing charging current.

STEP 4: CONTROLLED CURRENT CHARGE

: Adjusts the charging current intelligently.

STEP 5: ANALYSING 2

: Tests if the battery can absorb charge.

STEP 6: CONSTANT OUTPUT CHARGE

: Charges with constant voltage and 

compensates for any fake full charge caused by high current charging.

STEP 7: RECOVERY CYCLE CHARGE

: Absorbs more charge and compensates for 

the side effect of reduced charging current. 
 

STEP 8: ABSORPTION

: Charges with constant trickle current for maximum battery 

voltage.

STEP 9: ANALYSING 3

: Tests if the battery can hold charge.

STEP 10: MAINTENANCE

: Continuously monitors the battery, and charges with 

trickle current once the voltage is lower than threshold.

Summary of Contents for 6267017





















Reviews:

No comments