Clarke 3120181 Operating & Maintenance Instructions Download Page 2

2

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

INTRODUCTION

Thank you for purchasing this CLARKE Sabre Saw, suitable for cutting metal, 
wood, polymers and other materials.

Before attempting to use this product, please read this manual thoroughly and 
follow the instructions carefully. In doing so you will ensure the safety of yourself 
and that of others around you, and you can look forward to your purchase 
giving you long and satisfactory service.

Please keep these instructions for future reference.

SAFETY SYMBOLS

Please read all of the safety and operating instructions carefully before using 
this product. The following safety symbols are to be found on the machine.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12 
months from the date of purchase. Please keep your receipt which will be 
required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or 
tampered with in any way, or not used for the purpose for which it was 
intended.

Faulty goods should be returned to their place of purchase, no product can 
be returned to us without prior permission.

This guarantee does not effect your statutory rights.

Read this instruction 
booklet carefully 
before use.

Wear ear protection

Wear eye protection

Summary of Contents for 3120181

















Reviews: