Clarity C120HS User Manual Download Page 6

Page: 6 / 23

oid the warranty. For service or
repairs, call 1-800-552-3368.
h) Connection to party line service
is subject to state tariffs. Contact the
state public utility commission, public
service commission or corporation
commission for information.
i) If your home has specially wired
alarm equipment connected to the
telephone line, ensure the installation
of this telephone equipment does
not disable your alarm equipment. If
you have questions about what will
disable alarm equipment, consult your
telephone company or a
qualiﬁed installer.

Customer-Owned Coin/Credit
Card Phones:

To comply with state tariffs, the
telephone company must be given
notiﬁcation prior to connection. In
some states, the state public utility
commission, public service commis-
sion or corporation commission must
give prior approval of connection.

Part 15 of FCC Rules
Information

This device complies with Part 15 of
the FCC Rules. Operation is subject
to the following two conditions: (1)
This device may not cause harmful
interference, and (2) this device must
accept any interference received,
including interference that may cause
undesired operation.
Your equipment has been tested and
found to comply with the limits of

a Class B digital device, pursuant to
Part 15 of FCC rules. These limits
are designed to provide reasonable
protection against harmful interfer-
ence in residential installation.
This equipment generates, uses and
can radiate radio frequency energy
and, if not installed and used in
accordance with the instructions,
may cause harmful interference to
radio communications. However, there
is no guarantee that interference will
not occur in a particular installation;
if this equipment does cause harmful
interference to radio or television
reception, which can be determined
by turning the equipment
off and on, you are encouraged to try
to correct the interference by one
of the following measures:
1.  Where it can be done safely,

reorient the receiving television

or radio antenna.

2. To the extent possible, relocate

the television, radio or other

receiver with respect to the

telephone equipment. (This

increases the separation between

the telephone equipment and

the receiver.)

3. Connect the telephone equip-

ment into an outlet on a circuit

different from that to which the

television, radio, or other receiver

is connected.

4. Consult the dealer or an experi-

enced Radio/TV Technician

for help.

REGULATORY COMPLIANCE

CAUTION:

Changes or modiﬁca-

tions not expressly approved by the
manufacturer responsible for compli-
ance could void the user’s authority
to operate the equipment.

Industry Canada Technical
Speciﬁcations

This product meets the
applicable Industry Canada
technical speciﬁcations.

Before installing this equipment, users
should ensure that it is permissible
to be connected to the facilities of
the local telecommunications com-
pany. The equipment must also be
installed using an acceptable method
of connection. In some cases, the
company’s inside wiring associated
with a single line individual service
may be extended by means of a certi-
ﬁed connector assembly (telephone
extension cord). The customer should
be aware that compliance with the
above conditions may not prevent
degradation of service in some situa-
tions. Repairs to certiﬁed equipment
should be made by an authorized
Canadian maintenance facility desig-
nated by the supplier.
Any repairs or alterations made
by the user to this equipment, or
equipment malfunctions, may give the
telecommunications company cause
to request the user to disconnect
the equipment.

Users should ensure for their own
protection that the electrical ground
connections of the power utility,
telephone lines and internal metallic
water pipe system, if present, are
connected together. This precaution
may be particularly important in
rural areas.

CAUTION:

Users should not

attempt to make such connections
themselves, but should contact
the appropriate electrical inspec-
tion authority, or electrician, as
appropriate.
The Ringer Equivalence Number
is an indication of the maximum
number of terminals allowed to be
connected to a telephone interface.
The termination on an interface
may consist of any combination of
devices subject only to the require-
ment that the sum of the Ringer
Equivalence Numbers of all the
devices does not exceed ﬁve.
(The term “IC:” before the certi-
ﬁcation/registration number only
signiﬁes that the Industry Canada
technical speciﬁcations were met.)