background image

52

VRX633R

English

Installation and Wire

connection manual

1:When the unit is installed in a 1998 or later Volkswagen model, make sure to interrupt the

<<Remote>> output. Disconnect the <<blue/white>> wire and insulate the front ends of this lead.

A breakdown may occur if the lead is not disconnected, or front ends are not insulated.

2:In certain vehicles - Volkswagen/Opel/Vauxhall - it is necessary to exchange the accessory

<<Red>> and the main power <<Yellow>> connection, to avoid overload and loss of memory.

3:Connecting the PHONE MUTE Terminal

The lead included with the unit must be connected to the specified position of the vehicle’s ISO

connector in order to use the “triggered audio mute for cellular telephones” function.

4:Use the attached extension lead when necessary.

5:When connecting CCD CAMERA, be sure to connect RCA as well as the 8-pin Mini-Din video jack.

Note : Before making any installation, disconnect the car battery - (negative) cable.

3

7

7

1

2

!

4

5

6

8

@

B-1

B-6

B-5

B-7

B-8

B-4

B-3

B-2

A-4

A-6

A-8

A-7

9

A-5

1

2

2

3

4

5

5

Front right

Front left

Rear right

Rear left

Red

Red

White

White

Gray

Brack

Gray

Brack

0

Rear view of the Main unit

 

8.

WIRE CONNECTION

No.

Description

1

NAVI/CCD terminal

2

RGB INPUT

3

VIDEO INPUT (for TV tuner)

4

Radio antenna jack (

4)

5

CeNET terminal

6

Fuse (15A)

7

Phone mute (Brown)

8

Spare terminal (Yellow)

9

ISO CONNECTOR

0

AUDIO 4CH. OUTPUT

!

DVD/etc. INPUT
(for DVD changer and etc.)

@

Parking brake (Bright Green)

No.

Description

REAR RIGHT

B

REAR RIGHT

v

FRONT RIGHT

B

FRONT RIGHT

v

FRONT LEFT

B

FRONT LEFT

v

REAR LEFT

B

REAR LEFT

v

+12 V MAIN POWER (

2)

AUTO ANTENNA (

1)

ILLUMINATION
+12 V ACCESSORY (

2)

GROUND

B-1

B-2

B-3

B-4

B-5

B-6

B-7

B-8

A-4

A-5

A-6

A-7

A-8

Summary of Contents for VRX633R











Reviews: