background image

VRX633R

47

English

Installation and Wire

connection manual

1. BEFORE STARTING ................................................................ 47

2. PACKAGE CONTENTS ............................................................ 47

3. GENERAL CAUTIONS ............................................................. 48

4. CAUTIONS ON INSTALLATION .............................................. 48

5. INSTALLING THE MAIN UNIT ................................................. 49

6. REMOVING THE MAIN UNIT .................................................. 51

7. CAUTIONS ON WIRING .......................................................... 51

8. WIRE CONNECTION ............................................................... 52

9. SAMPLE SYSTEMS ................................................................ 54

■ 

Contents

VRX633R

1. This set is exclusively for use in cars with a

negative ground 12 V power supply.

2. Read these instructions carefully.

3. Be sure to disconnect the battery “ ” termi-

nal before starting. This is to prevent short
circuits during installation. (Figure 1)

1

Main unit

2

Manuals

Owner’s manual & Installation manual

Warranty card

3

Power supply lead

4

Bag for accessories of the main unit (No. 1)

Flat head screw (M5 

×

 8)............................4

Sems hexagonal bolt (M5 

×

 8)....................5

5

Bag for accessories of the main unit (No. 2)

Hook plate..................................................2

Cord clamp

Spacer

Special screw

6

Universal mounting bracket

7

Remote control unit

8

Battery

(for remote control unit)

9

Outer Escutcheon

0

DCP Case

 

1.

BEFORE STARTING

 

2.

PACKAGE CONTENTS

Installation and Wire connection manual

Summary of Contents for VRX633R











Reviews: