manualshive.com logo in svg

Clarion UNGO MS8200, Installation Manual

Share
Download
Clarion UNGO MS8200 Installation Manual Download Page 25

When the minimum or maximum sensitivity levels have been reached, the siren will
emit 4 quick chirps.

5.  Once you are satisfied with the Interior zone sensitivity setting, press the Mode Button,

then Button 2 to begin adjusting the Exterior zone.

•  The siren will chirp 4 times, the Exterior zone can be adjusted.

6.  Test the Exterior zone sensitivity.

•  Each time the sensor detects movement, the siren will chirp 2 times and the LED on

the sensor will light green.

7.  To make adjustments:

Press Button 1 to increase the sensitivity.
Press Button 2 to decrease the sensitivity.

•  The siren will emit one long chirp when the sensitivity is 

increased and two long

chirps when the sensitivity is 

decreased.

When the minimum or maximum sensitivity levels have been reached, the siren will
emit 4 quick chirps.

You may return to Interior zone adjustment at any time by pressing the Mode Button.
then Button 1.

•  The siren will chirp 3 times to indicate the Interior zone can be adjusted.

8.  Once you are satisfied with the sensitivity, turn the ignition key off.

MS8200 / MS8300 Installation Manual  -  Page  23

installation_rev3.qxd  7/26/99  6:07 PM  Page 23

Summary of Contents for UNGO MS8200































Reviews:

No comments

Brands by name

Popular brands

Load more brands