background image

44

VRX630

English

Installation and Wire

connection manual

1. Do not open the case. There are no user ser-

viceable parts inside. If you drop anything into
the unit during installation, consult your
dealer or an authorized CLARION service
centre.

2. Use a soft, dry cloth to clean the case. Never

use a rough cloth, thinner, benzine, or alco-
hol, etc. For tough dirt, apply a little cold or
warm water to a soft cloth and wipe off the
dirt gently.

1.

Prepare all articles necessary for installing
the main unit before starting.

2.

This model is used with the LCD panel slid
forwards (shell loading system). On some
types of cars, the LCD panel may touch the
dashboard or shift lever, in which case it can-
not be installed. Check that the set will not
hamper operation of the shift lever before
choosing the place of installation.(Figure 2)

3.

Install the unit within 30° of the horizontal
plane. (Figure 3)

4.

If you have to do any work on the car body,
such as drilling holes, consult your car dealer
beforehand.

5.

Use the enclosed screws for installation. Us-
ing other screws can cause damage.

(Figure 4)

 

3.

GENERAL CAUTIONS

 

4.

CAUTIONS ON INSTALLATION

T

N

N

T

N

T

6. The source unit has mounting screw holes

for NISSAN (N marks) and TOYOTA (T marks)
vehicles.

Summary of Contents for pro audio vrx 630











Reviews: