COMPONENTS
PE-3041B-A/PE-3041K-A/B
1.
Source unit
1
2.
Remote control unit
RCB-176-200
1
3.
Battery(CR2025)
1
4.
Mounting bracket(PE-3041B-A)
300-8088-00
1
5.
Mounting bracket(PE-3041K-A/B) 300-7742-00
1
6.
Mounting bracket(PE-3041K-A/B) 300-4976-00
1
7.
DCP case
335-6035-04
1
8.
Escutcheon(OUT-ES)
370-6226-04
1
9.
Extension lead
854-6433-50
1
10.
RCA PIN CORD
855-5520-56
1
11.
Parts bag
11-1. Removal key
331-2497-00
2
11-2. Part screw(M1.7x6)(PE-3041B-A)
716-0872-61
1
11-3. Screw(M5x8)
716-0496-51
1
1
-2-
To engineers in charge of repair or
inspection of our products.
Before repair or inspection, make sure to follow the
instructions so that customers and Engineers in charge
of repair or inspection can avoid suffering any risk or
injury.
1. Use specified parts.
The system uses parts with special safety features against fire
and voltage. Use only parts with equivalent characteristics
when replacing them.
The use of unspecified parts shall be regarded as remodeling
for which we shall not be liable. The onus of product liability
(PL) shall not be our responsibility in cases where an accident
or failure is as a result of unspecified parts being used.
2. Place the parts and wiring back in their original positions after
replacement or re-wiring.
For proper circuit construction, use of insulation tubes, bond-
ing, gaps to PWB, etc, is involved. The wiring connection and
routing to the PWB are specially planned using clamps to keep
away from heated and high voltage parts. Ensure that they are
placed back in their original positions after repair or inspec-
tion.
If extended damage is caused due to negligence during re-
pair, the legal responsibility shall be with the repairing com-
pany.
3. Check for safety after repair.
Check that the screws, parts and wires are put back securely
in their original position after repair. Ensure for safety reasons
there is no possibility of secondary ploblems around the re-
paired spots.
If extended damage is caused due to negligence of repair, the
legal responsibility shall be with the repairing company.
4. Caution in removal and making wiring connection to the parts
for the automobile.
Disconnect the battery terminal after turning the ignition key
off. If wrong wiring connections are made with the battery con-
nected, a short circuit and/or fire may occur. If extensive dam-
age is caused due to negligence of repair, the legal responsi-
bility shall be with the repairing company.
5. Cautions in soldering
Please do not spread liquid flux in soldering.
Please do not wash the soldering point after soldering.
6. Cautions in soldering for chip capacitors
Please do not heat the chip capacitors with a soldering iron
directly.
7. Cautions in handling for chip parts.
Do not reuse removed chips even when no abnormality is ob-
served in their appearance. Always replace them with new
ones. (The chip parts include resistors, capacitors, diodes, tran-
sistors, etc).
Please make an operation test after replacement.
8. Cautions in handling flexible PWB
Before working with a soldering iron, make sure that the iron
tip temperature is around 270
. Take care not to apply the
iron tip repeatedly(more than three times)to the same patterns.
Also take care not to apply the tip with force.
9. Turn the unit OFF during disassembly and parts replacement.
Recheck all work before you apply power to the unit.
DXZ785USB/DXZ786USB
Please solder the chip capacitors after pre-heating for replace-
ment because they are very weak to heat.
11-4. Rubber part
345-3799-20
8
* Use only compact discs bearing the
or
mark.
Some CDs recorded in CD-R/CD-RW mode may not be usable.
* Windows Media , and the Windows
logo are trademarks, or re-
gistered trademarks of Microsoft Corporation in the United States
and/or other countries.
*
WMA is the abbreviation of Windows Media Audio, an audio file
format developed by Microsoft Corporation.
* This product includes technology owned by Microsoft Corporation
and cannot be used or distributed without a license from MSLGP.
* As for this model, the tuner of the DSP type is used.When you
exchange it due to the tuner pack(BL1:880-2091E) trouble, it is
necessary to adjust for S-meter etc.Special JIG is necessary for
an accurate adjustment.The procedure document for the exclusive
use jig is appended to it.
* This DSP IC SAF7730HN219A(051-6706-40) of main PWB is ex-
posed die soldering pad type. The middle of this IC package is so-
ldered with the main PWB, and it cannot remove in an ordinary s-
oldering iron.Please use special removal JIG at the time of IC exc-
hange.
* This unit is compatible with USB 1.1/2.0 with maximum data tran-
sfer rates of 12 Mbps.USB memory devices that can be played by
connecting to the unit's USB connector are limited to those recog-
nized as "USB mass storage class devices"; operation is not gua-
ranteed with all USB memory devices.
* To prevent the accidental loss of data, always back up important
data on your computer.
* This unit does not support connections to a computer.In addition,
connections made through a USB hub device are also not
supported.
* This unit supports USB Digital Media Streaming.USB Digital Media
Streaming is a function used to play music files transmitted using
Media Transfer Protocol (MTP). This function also supports the
playback of WMDRM 10 files.
* Insert and remove a USB memory device only when the device is
not being accessed. Connecting or disconnecting the device at the
following times may result in the loss of data:
- If the USB memory device is removed or power is disconnected
during writing to the device.
* iPod
is for legal or rightholder-authorized copying only. Don't st-
eal music. iPod is a trademark of Apple Computer, Inc., registered
in the U.S and other countries.
