-7-
DXZ745MP/DXZ746MP
052-5055-11
MBM29DL800BA-90PFTN
8 M bit Flash Memory
1. Terminal Description
pin
1: Address 15
: IN : Address signal input.
pin
2: Address 14
: IN : Address signal input.
pin
3: Address 13
: IN : Address signal input.
pin
4: Address 12
: IN : Address signal input.
pin
5: Address 11
: IN : Address signal input.
pin
6: Address 10
: IN : Address signal input.
pin
7: Address 9
: IN : Address signal input.
pin
8: Address 8
: IN : Address signal input.
pin
9: NU
: - : Not in use.
pin 10: NU
: - : Not in use.
pin 11: WE
: IN : Write enable signal input.
pin 12: RESET
: IN : Reset signal input.
pin 13: NU
: - : Not in use.
pin 14: NU
: - : Not in use.
pin 15: Ready/Busy
: O : Ready/Busy flag output, H = Ready.
pin 16: Address 18
: IN : Address signal input.
pin 17: Address 17
: IN : Address signal input.
pin 18: Address 7
: IN : Address signal input.
pin 19: Address 6
: IN : Address signal input.
pin 20: Address 5
: IN : Address signal input.
pin 21: Address 4
: IN : Address signal input.
pin 22: Address 3
: IN : Address signal input.
pin 23: Address 2
: IN : Address signal input.
pin 24: Address 1
: IN : Address signal input.
pin 25: Address 0
: IN : Address signal input.
pin 26: CE
: IN : Chip enable signal input.
pin 27: VSS
: - : Negative supply voltage.
pin 28: OE
: IN : Output enable signal input.
pin 29: DQ 0
:I/O: The data input / output.
pin 30: DQ 8
:I/O: The data input / output.
pin 31: DQ 1
:I/O: The data input / output.
pin 32: DQ 9
:I/O: The data input / output.
pin 33: DQ 2
:I/O: The data input / output.
pin 34: DQ 10
:I/O: The data input / output.
pin 35: DQ 3
:I/O: The data input / output.
pin 36: DQ 11
:I/O: The data input / output.
pin 37: VCC
: - : Positive supply voltage.
pin 38: DQ 4
:I/O: The data input / output.
pin 39: DQ 12
:I/O: The data input / output.
pin 40: DQ 5
:I/O: The data input / output.
pin 41: DQ 13
:I/O: The data input / output.
pin 42: DQ 6
:I/O: The data input / output.
pin 43: DQ 14
:I/O: The data input / output.
pin 44: DQ 7
:I/O: The data input / output.
pin 45: DQ 15/A-1
:I/O: The data input/output, The Address signal
input.
pin 46: VSS
: - : Negative supply voltage.
pin 47: BYTE
: IN : The data length selection(8bit/16bit).
pin 48: Address 16
: IN : Address signal input.
051-6399-00
TC94A15F
CD IC
1.Terminal Description
pin
1: IPF OUT
: O : IP flag output.
pin
2: SB OK O
: O : Sub code Q data CRCC OK signal output.
pin
3: CLOCKIO
:I/O: The clock pulse input/output for the sub
code reading.
pin
4: VDD
: - : Positive supply voltage.
pin
5: VSS
: - : Negative supply voltage.
pin
6: DATA
: O : DATA
pin
7: SF SY O
: O : Playback frame synchronous signal output.
pin
8: SB SY O
: O : Sub code block synchronous signal output.
pin
9: HSO
: O : The play speed flag output.
pin 10: UHSO
: O : The play speed flag output.
pin 11: AR SEL IN
: IN : Fix to the high level.
pin 12: AWRC
: O : The control signal output for the active
wide range VCO.
pin 13: P VDD
: - : PLL positive supply voltage.
pin 14: PDO
: O : Phase difference signal output of EFM-
PLCK.
pin 15: TMAX S
: O : T max judgment output.
pin 16: TMAX
: O : T max judgment output.
pin 17: LPF N
: IN : Inverted input of LPF for PLL.
pin 18: LPF OUT
: O : The output terminal for the Low Pass Fil-
ter.
pin 19: P Vref
: - : PLL reference voltage.
pin 20: VCO FILTER
: O : Loop filter for VCO.
pin 21: VCO Ref
: IN : VCO reference voltage input.
pin 22: DTC N
: O : For the analog slicer.
pin 23: DTC P
: O : For the analog slicer.
pin 24: PLL VSS
: - : PLL ground.
pin 25: SLCO
: O : Output of internal DAC for data slice level
generation.
pin 26: RF IN
: IN : RF signal input.
pin 27: RF RP
: IN : RF ripple input.
pin 28: RF EQ OUT
: O : The output of the RF equalizer.
pin 29: A VDD
: - : Positive supply voltage for the Analog sec-
tion.
pin 30: RES IN
: - : For reference current setting.
pin 31: Vref OUT
: O : The reference voltage output.
pin 32: VMDIR
: O : The reference voltage output.
pin 33: TESTR
: O : The compensation terminal for RFEQO off-
set.
pin 34: INVSEL
: IN : MDI polarity selection.
pin 35: AGCI
: IN : The input terminal of RF AGC amplifier.
pin 36: RF DCI
: IN : The input terminal for RF peak detection.
pin 37: RF OUT
: O : RF signal output.
pin 38: PN SEL
: IN : The transistor type selection input for laser
diode driver. L=NPN, H=PNP.
pin 39: EQ SET
: O : The equalizer setting terminal.
pin 40: RF VDD
: - : RF power supply.
pin 41: LDO
: O : The laser diode drive output.
pin 42: MDI
: IN : Monitor photo diode signal input.
pin 43: RF VSS
: - : RF ground.
pin 44: FNI 2
: IN : Main beam signal input.
pin 45: FNI 1
: IN : Main beam signal input.
pin 46: FPI 2
: IN : Main beam signal input.
pin 47: FPI 1
: IN : Main beam signal input.
pin 48: TPI
: IN : Sub beam signal input.
pin 49: TNI
: IN : Sub beam signal input.
pin 50: FTEO
: O : For test.
pin 51: RF ZI
: IN : RF ripple zero cross signal input.
pin 52: A VSS
: - : Analog ground.
pin 53: RF RP
: O : RF ripple signal output.
pin 54: RF DC
: O : RF peak detection signal output. (hologram
suitable)
pin 55: FEI
: O : Focus error signal output.
pin 56: SBAD
: O : Sub beam add signal output.
pin 57: TEI
: O : Tracking error signal output.
pin 58: TE Z IN
: IN : Tracking error signal inpur for zero cross.
pin 59: A VDD
: - : Positive supply voltage for the Analog sec-
tion.
pin 60: FOO
: O : Focus equalizer output.
pin 61: TRO
: O : Tracking equalizer output.
pin 62: Vref
: O : Reference voltage output.
pin 63: FMO
: O : Field equalizer output / Speed error output.
pin 64: DMO
: O : Disk equalizer output.
pin 65: IO2A
:I/O: General input/output.
pin 66: IO3A
:I/O: General input/output.
pin 67: MONIT
: O : Internal DSP signal monitor.
pin 68: FG IN
: IN : FG input for the spindle CAV servo.
pin 69: VSS
: - : Negative supply voltage.
pin 70: VDD
: - : Positive supply voltage.
pin 71: TESIN
: IN : For test.
pin 72: X VSS
: - : Master clock analog ground.
pin 73: X IN
: IN : Crystal connection.
pin 74: X O
: O : Crystal connection.
pin 75: X VDD
: - : Clock power supply.
pin 76: D VSS
: - : Digital ground.
pin 77: RO
: O : Right channel data output for 1-bit DAC.
pin 78: D VDD
: - : Positive supply voltage for the digital sec-
tion.
pin 79: D Vref
: O : Digital reference voltage.
pin 80: LO
: O : Left channel data output for 1-bit DAC.
pin 81: D VSS
: - : Digital ground.