Clarion CX201, Owner'S Manual

Page: 10 / 33

Basic Operations
E
nglis
h
10
CX201
3-1. Each time yo u t u rn the [ ROTARY ] kno b ,
the tone effect changes in the following
order:
“ CUSTOM ”
↔
“ EXCITE ”
↔
“ IMPACT ”
↔
“ B-BOOST ”
↔
“ OFF ”
CUSTOM : u ser c u stom
EXCITE : b ass and tre b le emphasized
mid emphasized
IMPACT : b ass and tre b le emphasized
B-BOOST : b ass emphasized
OFF : no so u nd effect
When “CUSTOM” is set:
3-1. Press the [ ROTARY ] kno b .
3-2. Press the [
x
] or [
v
] bu tton to select the
“ BASS ” , “ MID ” or “ TREBLE ” mode to
adj u st.
3-3. If yo u want to set the flat, press the
[ ROTARY ] kno b to ret u rn to the “ CUSTOM ”
mode, then press and hold the [ ROTARY ]
kno b (1 sec.), b ass/mid/tre b le
characteristics b ecome flat and switch to
the “ CUSTOM ” mode.
When “EXCITE/IMPACT/B-BOOST” is set:
3-1. Press the [ ROTARY ] kno b .
3-2. T u rn the [ ROTARY ] kno b to adj u st the
setting in the range of -3 to +3.
∗
The factory defa u lt setting is “ 0 ”.
3-3. Press the [ ROTARY ] kno b to ret u rn to the
pre v io u s mode.
●
Adjusting the BASS/MID/TREBLE
This adj u stment can b e performed only when
the BEAT EQ is set to “ CUSTOM ”.
Note:
• While connected with the external amplifiers,
please do not set the “BASS/MID/TREBLE” in
the maximum level. Otherwise the speakers may
be damaged.
3-1. Press the [ ROTARY ] kno b .
3-2. T u rn the [ ROTARY ] kno b to select as
following order:
“ BASS<G> ”
↔
“ BASS<F> ”
↔
“ BASS<Q> ”
↔
“ MID<G> ”
↔
“ MID<F> ”
↔
“ MID<Q> ”
↔
“ TREBLE<G> ”
↔
“ TREBLE<F> ”
↔
“ TREBLE<Q> ”
∗
The factory defa u lt setting is “ BASS <G> ”.
3-3. T u rn the [ ROTARY ] kno b to select the
setting.
BASS<G> :The factory defa u lt setting is “ 0 ”.
(Adj u stment range: +7 to –7)
BASS<F> : The factory defa u lt setting is “ 50 ”.
(Adj u stment range: 50/100/200)
BASS<Q> :The factory defa u lt setting is “ 1 ”.
(Adj u stment range: 0.7/1/1.4/2)
MID<G> : The factory defa u lt setting is “ 0 ”.
(Adj u stment range: +7 to -7)
MID<F> : The factory defa u lt setting is “ 500 ”.
(Adj u stment range: 500/1K/2K)
MID<Q> : The factory defa u lt setting is “ 1 ”.
(Adj u stment range: 0.7/1/1.4/2)
TREBLE<G> :The factory defa u lt setting is “ 0 ”.
(Adj u stment range: +7 to -7)
TREBLE<F> :The factory defa u lt setting is
“ 10K ”.
(Adj u stment range: 5K/10K/15K)
TREBLE<Q> :The factory defa u lt setting is “ 1 ”.
(Adj u stment range: 0.7/1/1.4/2)
3-4. Press the [ ROTARY ] kno b to ret u rn to the
pre v io u s mode.
●
Setting the MAGNA BASS EXTEND
The MAG N A BASS EXTE N D does not adj u st
the low fre qu encies like the normal so u nd
adj u stment f u nction, bu t emphasizes the deep
b ass fre qu encies to pro v ide yo u with a dynamic
so u nd.
∗
The factory defa u lt setting is “ OFF ” (off).
2-1. Select “ M-B EX ”.
3-1. T u rn the [ ROTARY ] kno b to select “ ON ” or
“ OFF ”.
●
Adjusting the balance
2-1. Select “ BALANCE ”.
3-1. T u rn the [ ROTARY ] kno b to adj u st the
b alance of the right and left speakers.
∗
The factory defa u lt setting is “ CENTER ”
(center). (Adj u stment range: RIGHT12 to
LEFT12 (right 12 to left 12))
●
Adjusting the fader
2-1. Select “ FADER ”.
3-1. T u rn the [ ROTARY ] kno b to adj u st the
b alance of the rear and front speakers.
∗
The factory defa u lt setting is “ CENTER ”
(center). (Adj u stment range: FRO N T12 to
REAR12 (front 12 to rear 12))
●
Setting the subwoofer
Yo u can set the low pass filter of s ub woofer.
This adj u stment can b e performed only when
the “ REAR/S-W ” is set to “ S-WOOFER ”.
2-1. Select “ LPF ”.
CX201_EN.book Page 10 Wednesday, November 17, 2010 10:50 AM