Installation Procedure
The wall surface must be of suitable strength and construction.
1) Carefully remove the mirror by unfastening the retaining screws
on the top and bottom of the mirror body and remove from the
main body. The heated mirror pad should be disconnected
byseparating the plug. Place the mirror, screws and washers in a
safe place for now.
2) Mark the desired height of the mirror and draw a horizontal line
on the wall (using a spirit level). Holding the mirror body in place
on the horizontal line, mark off all 4 holes in the back of the mirror
body. Also mark off where the electrical supply cable must be
p l a c e d i n c a s e t h i s n e e d s t o b e c h a s e d o u t l o c a l l y f o r t h e
installation. Place the mirror body to one side and drill the holes as
necessary for the wall plugs. Insert the wall plugs and screw the
mirror body in position having fed the power supply cable through
the rubber grommet in the mirror body. Make sure that all screws
are secure.
Note: Wall plugs provided are suitable for Stone or Brick walls.
For other wall types use appropriate wall plugs. If in doubt consult
an expert.
3) Ensure that the electrical supply is turned off at the mains.
Remove the cover from the connection box inside the mirror body
to allow the electrical connections to be made as follows:
Strip the mains PVC supply cable as necessary. Thread the power supply through the rubber grommet on
the switch box and make the necessary connections in accordance with the current IEE Regulations.
Firmly tighten all terminal connections. Make sure that the cable is clamped securely in the cord anchor
inside the connection box. Refasten the cover on the connection box making sure that it fits securely.
IMPORTANT: Loose connections can lead to over heating. Excessive temperatures may lead to scorching
of the plastic components, and in extreme cases may even melt. Charring of components is always a
consequence of faulty installation or maintenance, and any claims are excluded from the warranty.
4) Reconnect the heated demister pad.
Strip wires to a suitable
length. DO NOT connect
to a plug & socket outlet.
THIS PRODUCT IS MANUFACTURED TO CLASS I
CATEGORY AND MUST HAVE AN EARTH CONNECTION.
! IF IN DOUBT CONSULT YOUR ELECTRICIAN !
COLOUR CODING:
L - Live
= Brown
N - Neutral = Blue
- Earth = Green & Yellow
Mirror for illustrative purposes only.
Please match your components to the relevant diagram
3
4
2
1
5) Replace the mirror and its frame inside the body, aligning the holes. Make sure that the glass fits
completely flat on the face of the body. Fasten with the screws and washers removed in stage 1. Turn back
on the electrical supply so that your Mirror is operational.
Operating Instructions
• To turn ON or OFF the LEDs, wave the hand across the IR sensor.
• The demister pad will be ON when the lights are. DO NOT leave on for prolonged periods of time.
• P
airing Bluetooth
®
enabled devices:
Pairing occurs when two Bluetooth
®
wireless technology enabled devices communicate with each other
and establish a connection. This information is then stored in the memory of each device meaning that
once initially connected, the two devices will not need to pair again.
•
Connecting your Bluetooth
®
enabled device to your mirror:
1. It is recommended that the Bluetooth
®
connectivity of the device you want to pair with your mirror is
turned on first to make connection easier.
2. The Bluetooth module will be ON when the lights are by waving the hand across the IR sensor. The
mirror will beep to signal that the Bluetooth
®
has been turned ON.
3. On the selected Bluetooth
®
enabled device select the mirror from the Bluetooth
®
device list to connect.
4. The mirror will beep twice to signal that a connection has been made between the two Bluetooth
®
enabled devices. Once connected, any music played on the paired device will play through the mirror.
The Bluetooth
®
connection will automatically cease when the two paired devices are out of range.
Cleaning
It is recommended that the unit is cleaned with a soft, dry, non abrasive cloth when turned off. Never use
cleaning agents or abrasive materials on any type of surface finish. Do not allow moisture to come into
contact with the electrical components.
Compliance
This product complies with all relevant British and European safety standards
Lights
To obtain a replacement LED lamp if faulty or broken contact customer services (see back page) quoting
product code.
Wiring
This product is manufactured to class I category and must have an earth connection
COLOUR CODING:
L - Live = Brown
N - Neutral = Blue
- Earth = Green & Yellow