LF.10.17.V1
Tavistock, Brassmill Lane Trading Estate, Bath, BA1 3JF
t. 01225 787 870 e. [email protected] w: www.tavistock-bathrooms.co.uk
ILLUMINATED MIRROR
WITH BLUETOOTH
®
WIRELESS TECHNOLOGY
INSTALLATION & AFTERCARE INSTRUCTIONS
CLARION - CL70AL
Electrical Safety Instructions
All fittings must be installed by a competent person, in accordance with current IEE wiring regulations.
If in doubt consult a qualified electrician.
Important
Always switch off the electrical supply at the mains during installation and maintenance. It is recommended
that the fuse is withdrawn or the circuit breaker is switched off for the necessary circuit before installation
commences.
The product must be installed with a minimum distance of 150mm between the infrared
sensor and an adjacent wall or obstruction to ensure correct function of the sensor.
Fitting in Bathrooms is subject to the appropriate zone in accordance with IEE Regulations. This product is
suitable for zone 2 and outside zones. IT IS NOT suitable for installation in Zone 0 or Zone 1. It is also not
suitable for installation in saunas, steam rooms or shower cubicles. This product is only suitable for
permanent installation. DO NOT connect to a trailing plug and socket outlet. Although this product has an
Ingress Protection rating of IP44 it is only suitable for indoor use. Do not attach the product to surfaces
that are damp or otherwise electrically conductive.
Installation Care & Safety
Wear suitable eye protection when drilling. Take care when using power tools near water - the use of a
residual current device (RCD) is advised. Beware of hidden cables or pipes. Take care if drilling on tiled
surfaces in case the drill slips. A piece of masking tape applied to the wall before marking out the fixing
holes will stop the drill from wandering.
DO NOT strike glass components with hard or pointed
items.
DO NOT place very hot or very cold items against or in
close proximity to glass surfaces unless an adequately
thick insulation material is used to prevent such items
coming in contact with the glass.
The nominal thickness of the mirror glass used in this
product is 5mm and is film backed for safety. If the glass
becomes chipped or broken replace immediately.
This product should be positioned well away from
curtains and other fabrics. Never cover the mirror. This
product is heated, we recommend that it is turned off
after use and should never be left on for prolonged
periods of time.
This product could be dangerous and is
only to be installed by a competent person.
2
2
2
OUTSIDE
ZONES
2
ZONE
1
0.75m
2.25m
3.0m
0.6m
0.6m
0.75m
BATHROOM ZONES DIAGRAM
Distances from a bath tub or shower tray
Troubleshooting
“There is no sound from my mirror.”
- The volume on either device is muted or turned down.
- There is a problem with the Bluetooth
®
connection - try erasing the connection on the audio device and
then re-pairing.
- There may be interference from other nearby Bluetooth
®
enabled devices - try turning them off.
- The connected devices are too far apart and out of range - try moving the devices closer together.
“I cannot pair the mirror with my Bluetooth
®
device.”
- The bluetooth module may not powered on. Try turning the mirror OFF and ON again, wait and listen
for the beeping sound that indicates that the module is ON and when selected to pair with your device
wait and listen for a second beep.
- The Bluetooth
®
capability of your chosen device is turned off or out of range.
- There was a problem during pairing - some devices will pair automatically when selected some will
require a pass code or acceptance of the connection before they will finalise the pairing.
- Refer to your Bluetooth
®
device’s instruction manual to ensure it supports the A2DP (stereo
Bluetooth
®
) profile.
“The sound quality is poor.”
- Your Bluetooth
®
device may be close to being out of range and should be moved closer to the mirror.
- For those devices that support the use of Apps, there may be too many running in the background which
can affect the amount of internal resources available on the device to transmit audio. Closing any
non-essential applications may improve audio quality.
- Similarly, if the selected device has Wi-Fi capabilities, turning this off may improve audio quality.
- There could have been a problem during the initial pairing of devices. Erase the connection using your
Bluetooth
®
device and re-pair.
“My
mirror is not automatically reconnecting with my Bluetooth
®
device.”
- The mirror will automatically reconnect with paired devices when both devices Bluetooth
®
capabilities
are turned on. Depending on the manufacturer of the Bluetooth
®
device, the order in which the devices
are turned on to automatically connect may vary. In some cases it will be necessary to turn on Bluetooth
®
capabilities on the audio device before turning on the mirror.
The Bluetooth
®
word mark and are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks
by Roper Rhodes is under license. Other trademarks and trade names are those of their respective owners.
