■
Adjusting camera angle (example)
When the camera angle has been changed, the range displayed by the image on the monitor will
change. Always confirm by direct observation when backing the vehicle.
Adjust the angle of
brackets A+B as
required by the
mounting position.
Adjust horizontal angle
while confirming image on
monitor.
CAUTION
5. WIRING
1
Lead the camera cable into the vehicle and align it along the vehicle weather stripping. Use the supplied
cable holders as necessary to fix the wires in place and prevent them from being pinched in hinges or
dampers.
2
Using an optional extension cable, the camera cable can be installed under the vehicle floor (carpet) to
connect to a Clarion vehicular monitor or independent power supply box (CAA-188/CAA-185).
Exclusive waterproof relay cable (sold separately)
Inside the vehicle
Outside the vehicle
Securely tighten the connectors.
CCD camera
CCD camera
power supply box
or
Clarion
vehicular monitor
ADJ
POWER
SELECT
IRIS
ZOOM
CAM1/DIM
MODE
CCA-532-100 (7 m)
CCA-533-100 (10 m)
CCA-534-100 (15 m)
■
Waterproof Connector Fastening Procedure and Cautions
1
w
Mark : Align the arrow marks on both connectors in order to connect the cable.
Exclusive waterproof
relay cable (female)
Camera cable (male)
2
Hold the two connectors together and twist the ring on the camera cable’s connector as far as it will go.
Twist the ring in the direction
of the arrow while holding both
connectors together.
Twist the yellow ring until there is no gap between the ring and the connector.
Should there be any gap between the ring and the connector, twist the ring to close it.
Gap
Note:
• See the Instruction Manual supplied with the
monitor for information regarding wiring, operation,
and composition of the monitor unit.
CAUTION
7. SPECIFICATIONS
Power source/voltage:
DC 9 V (±0.5 V)
Power consumption:
120 mA or less
Image sensor:
1/4" solid-state color CCD
Angle of view:
About 130° (horizontal)
About 97° (vertical)
Minimum subject illumination:
3 LUX or less (2 LUX ±1 LUX)
SN ratio:
48 dB or more (AGC-OFF)
Weight:
About 72 g (bracket and 0.5 m cable)
Dimensions:
27 (W)
×
25 (H)
×
28.3 (D) mm
Note:
• Specifications and design are subject to change without notice for further improvement.
6. TROUBLESHOOTING
Symptom
No image
Poor image is produced
Reason
Wiring is incomplete or disconnected.
A fuse is burned out.
The lens cover is soiled.
Sunlight or headlights from a vehicle
are shining directly in the camera.
The environment is too dark.
The level of illumination outside the
vehicle changed too abruptly.
1. When moving from a bright to a
dark location (especially from
bright sunlight to shade), the
image may appear excessively
dark.
2. When moving from a dark to a
bright location (especially from
shade into bright sunlight), the
screen image may appear
excessively bright.
Solution
Check wiring once again and confirm
correct connections.
When using an independent power
supply box, check the fuse and, if
burned out, replace with a new one
of the same capacity (1 A). If the fuse
burns out repeatedly, consult your
dealer or nearest Clarion Service
Center.
Wipe lightly with a damp soft cloth.
Do not rub harshly with dry cloths
since scratches may be produced.
The image will return to normal when
the light striking the lens is removed.
The image display will be poor at
night or in dim light.
The image will return to normal in
conditions of brighter illumination.
[When using a separate power
supply box]
• In auto mode
Stop the vehicle and set the
transmission to neutral, then once
again to reverse.
• In manual mode
Press the AUTO/MANUAL switch to
set the unit to AUTO, then press once
again to set to MANUAL. If the
transmission is in reverse, set it to
neutral before pressing the switch.
TEL :+49-6105-977-0
FAX :+49-6105-977-399
CE DECLARATION of CONFORMITY
We
Clarion Europa GmbH
(supplier's name)
Hessenring 19-21, 64546 Mörfelden-Walldorf, GERMA
NY
(address)
declare under our sole responsibility that the product
MODEL:
Product code: CC2012E
TYPE: 104CC20
(name, type or model, possibly sources and numbers of items)
to which this declaration relates is in conformity with the following
standard(s) or other normative document(s)
EN 61000-6-3:
EN
(title and/or number and date of issue of the standard(s) or
other normative document(s))
(if applicable) following the provisions of
2004/108/EC
Directive.
And following the provisions of
2004/104/EC
Directive,
according to paragraph 3.2.9 of Annex I,
meets the limits defined in paragraph 6.5, 6.6, 6.8 and 6.9 of Annex I
(supplier's comment)
Mörfelden-Walldorf GERMANY
Susumu Yamakawa
14 SEP 2007
President
(Place and date of issue)
(name and signature or equivalent
marking of authorized person)
RefNo 07RCSP001SP
D.F.DQC 06A145 and 07A135
CC2012
2001
61000-6-1:2001
CCD Video Camera
Output image change from the previous model
㧦
CC2011.
