CC-2012E
Vehicular Color CCD Camera (true image)
Installation manual
Printed in Japan 2007/9 284-1042-01
1. FEATURES
■
High-performance 1/4" color CCD solid-state imaging element
■
Wide-angle lens, allowing broad field of view
■
High-resolution glass lens for high image quality
■
True-image display is ideal for checking to front and side.
■
Small size and weight for easy installation
2. PRECAUTIONS
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to consult the dealer or an experienced radio/TV
technician for help.
INFORMATION FOR USERS:
CHANGES OR MODIFICATIONS TO THIS PRODUCT NOT APPROVED BY THE MANUFACTURER WILL
VOID THE WARRANTY AND WILL VIOLATE FCC APPROVAL.
• This device has been designed exclusively for use with a vehicular mounted television system. It
should not be used for other purposes.
• Disconnect the vehicle’s negative (–) terminal when installing wiring.
• Do not attempt to disassemble or modify this product.
• In the event it is necessary to drill holes in the vehicle for mounting, confirm that the drill bit or
camera wiring will not strike or interfere with piping, gas tank, electrical wiring or other functional
parts of the vehicle.
• Do not rely solely on the monitor image.
A vehicle-mounted camera/monitor system is an auxiliary device meant for confirming safety conditions
inside and to the front/rear of the vehicle, and it is limited in its range. In addition, the system produces a
wide-angle image, so actual distances to objects may be different than they subjectively appear in the
monitor. As a result, the system should be used only in conjunction with direct visual observations.
• Do not use when the imaging surface or other parts are malfunctioning.
• When installation and wiring are completed, confirm that the vehicle’s horn, brake and warning
lights, and other electrical equipment function properly as designed.
• Install only as directed in the Installation Manual.
• Install accessory parts as directed.
• When drilling holes in the vehicle for installation of wiring, always use insulated grommets in the
holes to protect the wiring.
• If holes are drilled in the vehicle to install the camera, or when installing wiring, use silicon sealant
to seal any gaps.
• Do not damage or scar the camera wiring.
• After completing the camera wiring, use cable clamps or insulation tape to bundle the wiring together.
• Do not use high-pressure car washing devices around the camera.
The camera is a high-precision instrument and should not be subjected to high-pressure water
stream impacts.
• Periodically check the tightness of the installation screws and retighten if necessary.
WARNING
CAUTION
3. PACKAGE CONTENTS
1
Camera (with 0.5 m cable) ............................. 1
2
Mounting bracket A ........................................ 1
3
Mounting bracket B ........................................ 1
4
Mounting bracket C ........................................ 1
5
Installation screws (hex head M3 x 6) ............ 4
6
Installation screws (pan head M3 x 6) ........... 2
7
Cleaning fluid (for use in preparing
surface for 2-sided tape) ................................ 1
8
Cable holders ................................................. 7
9
Cable clamps ................................................. 3
0
Owner’s manual & Installation manual ........... 1
0
2
3
5
8
9
7
4
6
1
4. INSTALLATION
Before installation
• Before installing the camera or its wiring, read all safety warnings and be sure to install the unit correctly.
• Before installing the camera permanently, use adhesive tape to mount the camera in its proposed position,
then check the image in the monitor to confirm proper display before fixing the camera in its final position.
• Disconnect the battery’s negative (–) terminal installing wiring.
Precautions when using two-sided tape for installation
■
Do not install on glass or body surfaces treated with fluorinated resins or other water-repellent
treatments.
■
Abide by the following rules in order to prevent lowering of the installation tape’s adhesion:
• As far as possible, install on a day with clear weather.
• Within the first 24 hours after installation, do not expose the installation to moisture (water, rain, mist, snow,
etc.), or subject the installation to strong forces or impacts.
• When installation must be performed under conditions of low ambient temperature (20°C or below), use a
hair dryer to warm the surface of the bracket where the 2-sided tape is to be applied.
• Do not touch the bracket-mounting surface’s 2-sided tape, and do not attempt to move or reset the tape
after initial application.
Installing the camera
1. Install mounting bracket B
Use the supplied cleaner to clean the vehicle surface to which the bracket is to be applied, then
remove the protective paper from the mounting surface of bracket B and press securely onto the
vehicle surface.
Notes:
• Before using the supplied cleaner, read the label on the cleaner container thoroughly.
• Do not wipe the camera body with the cleaner, since it may be discolored or otherwise damaged.
• Before removing the protective paper on the bracket, place it in the proposed position on the vehicle and
confirm that the surfaces match properly without gaps.
• When using screws to install the bracket, use the right-left screw holes provided on bracket B.
2. Install mounting bracket A
Using the supplied 2 installation screws (hex head M3 x 6), fasten bracket A to bracket B.
• While tightening the screws, adjust the angle of the bracket A to produce the optimum camera angle.
To mount the camera at a level angle, mount bracket A’s engraved leveling line (——) even with the center
of the installation screws when tightening.
Mounting bracket A
Mounting bracket B
Installation screws (hex head)
Angle adjustment direction
3. Attach mounting bracket C to camera
Using the two pan head installation screws (M3 x 6), attach the camera to mounting bracket C,
using the two hex head installation screws (M3 x 6) as shown, attach the camera and bracket C
assembly to mounting bracket A.
Mounting bracket A
Installation screws
(hex head)
Mounting bracket C
Camera
Installation screws
(pan head)
• Adjust the camera angle as desired when tightening the screws for mounting bracket C.
The camera’s position can be adjusted by selecting from among the three sets of holes on the sides of
mounting bracket A.
or
Use one of the three holes.
In addition, the mounting bracket A can be inverted (mounted
upside down) if needed to provide additional range of camera
installation.
Invert mounting bracket A
• When adjusting the camera position, do not allow the camera cable to be excessively stretched or
loose.
• Periodically check the tightness of the installation screws and retighten if necessary.
WARNING
CAUTION
